Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
4 Putting into operation
Tab. 2
Liquid cooling specifications/cable assembly specifications
Liquid cooling specifications
Flow pressure
All specifications relate to 4 m and 8 m cable assemblies.
Tab. 3
Product-specific torch data (EN 60974-7)
Type
Type of cooling
SR/ABITIG GRIP
24 G
Air
24 W
Liquid
ABITIG GRIP
12-1
Liquid
18 SC
Liquid
SR/ABITIG GRIP
9
Air
17
Air
26
Air
18
Liquid
20
Liquid
20SC
Liquid
SR (handle tube)
20
Liquid
1Pursuant to EN 60974-7, the alternating current (AC) must be specified with 70% of the tested direct current (DC).
3.2
Figures used
All figures can be found at the start of this document.
4
Putting into operation
WARNING
Electric shock due to touching live components
Touching live equipment parts may result in potentially fatal electric shocks.
► Only hold and move the welding torch using the intended handle piece.
WARNING
Electric shock due to damaged or improperly installed components
Damaged or improperly installed components may result in potentially fatal electric shocks. Components include: Welding torch, cable assembly, spare parts,
wear parts.
► Inspect all components prior to each use and check that all connections are duly installed and undamaged.
► Clean soiled components immediately.
► Replace damaged components immediately.
► Damaged, deformed or worn components must only be replaced by an electrician who has been trained by ABICOR BINZEL.
Perform the following activities prior to every use:
1 Inspect, clean and, if necessary, replace the welding torch.
2 Inspect, clean and, if necessary, replace the spare and wear parts.
4.1
Bending the flexible torch body (optional), Fig. 2
To extend the torch head's service life, please use the recommended
technique:
Type of cooling
Air-cooled
Liquid-cooled
Bending back to the initial position is classed as a bending cycle.
EN - 30
Min. 2.5 bar/max. 3.5 bar
Load
Duty cycle
1
DC
AC
A
A
%
110
80
35
140
100
100
400
280
100
400
280
100
110
80
35
140
100
35
180
130
35
320
230
100
240
170
100
320
220
100
220
150
100
Bending cycle
80 times
50 times
Cable assembly specifications
Cooling unit power
For further information regarding the available cable assembly designs and
performance data, please refer to the current order documentation.
Electrode Ø
Gas flow rate
mm
l/min
0.5–1.6
5–12
0.5–2.4
7–15
1.6–4.0
7–20
0.5–4.8
7–20
0.5–1.6
5–12
0.5–4.0
7–15
0.5–4.0
7–18
0.5–4.0
7–20
0.5–3.2
8–20
0.5–3.2
8–20
0.5–3.2
8–20
3 Inspect, clean and, if necessary, replace the cable assembly.
► Perform all the steps in the specified order.
► Support the torch head with the thumbs at this point (2) when
bending (1).
Max. bending angle
45°
45°
SR/ABITIG GRIP
Min. 800 W
Cooling
Supply temp.
Flow
Max.
Min.
50
0,7
50
0,8
50
0,8
50
0,8
50
0,7
50
0,7
50
0,7
Min. bending radius [mm]
25.0
25.0
Advertenties
Hoofdstukken
Inhoudsopgave
