Advertenties
Beschikbare talen
Beschikbare talen
The sawblade must not jam!
Storing the push rod (Fig. 17)
In order to have the push rod (R) to hand at all times,
hang it on the device (j) intended for this, at the top
left side of your band saw.
8.10 Transverse cutting gauge (14) (optional)
(Fig. 18)
• Slide lateral stop (o) into a groove (k) in the saw
bench.
• Release the grip screw (l).
• Turn the lateral stop (o) until the desired angular
dimension has been set. The arrow on the lateral
stop indicates the set angle.
• Retighten the grip screw (l).
• The stop rail (n) can be slid against the lateral
stop (o). To do so, loosen the knurled screws (m)
and slide the stop rail (n) into the desired position.
Tighten the knurled screws (m) again
• Attention! Do not slide the stop rail (n) too far in the
direction of the saw blade.
8.11 On/O昀昀 switch (Fig. 1)
• To turn the machine on, press the green button „1"
On/O昀昀 switch (10).
• To turn the machine o昀昀 again, press the red button
„0" On/O昀昀 switch (10).
• The band saw is equipped with an under voltage
switch. With a power failure, the band saw must
be switched back on again.
Attention!
When working with the machine, all protective devic-
es and guards must be 昀椀tted.
The upper and lower bandwheel is protected by a
昀椀xed guard and an articulated cover. When open-
ing the cover, the machine is switched o昀昀. Starting is
possible only with closed cover.
9. Transport
The machine must only be lifted and transported on
its frame or the frame plate. Never lift the machine at
the safety devices, the adjusting levers, or the saw-
ing table.
During the transport the saw blade protection must
be in the lowest position and near the table. Never
raise at the table!
Unplug the machine from the mains during transport.
32 | GB
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
10. Working instructions
The following recommendations are examples of the
safe use of band saws. The following safe working
methods should be seen as an aid to safety. They
cannot be applied suitably completely or comprehen-
sively to every use. They cannot treat every possible
dangerous condition and must be interpreted care-
fully.
• Connect the machine to a suction unit when work-
ing in closed rooms. A suction device which con-
forms with commercial regulations must be used
for suction in commercial areas.
• Loosen the sawband when the machine is not in
operation (e.g. after 昀椀nishing work). Attach a no-
tice on the tension of the saw band to the machine
for the next user.
• Collect unused sawbands and store them safely in
a dry place. Check for faults (teeth, cracks) before
use. Do not use faulty sawbands!
• Wear suitable gloves when handling sawbands.
• All protective and safety devices must be securely
mounted on the machine before beginning work.
• Never clean the sawband or the sawband guide
with a hand-held brush or scraper while the saw-
band is running. Resin-covered sawbands impair
working safety and must be cleaned regularly.
• For your own protection, wear protective glasses
and hearing protection. Wear a hairnet if you have
long hair. Roll up loose sleeves over the elbows.
• Always position the sawband guide as near the
workpiece as possible when working.
• Insure su昀케cient lighting in the work area and
around the machine.
• Always use the fence for straight cuts to keep the
workpiece from tipping or slipping away.
• When working on narrow workpieces with manual
feed, use the push stick.
• For diagonal cuts, place the saw bench in the ap-
propriate position and guide the workpiece on the
fence.
• Insure safe workpiece guidance.
• For arced and irregular cuts, push the workpiece
evenly using both hands with the 昀椀ngers togeth-
er. Hold the workpiece with your hands on a safe
area.
• Use a pattern for repeated arced or irregular cuts.
• Insure that the workpiece does not roll when cut-
ting round pieces.
• For safe work when transverse cutting, use the
special transverse cutting gauge accessory.
10.1 Performing longitudinal cuts (Fig. A)
Here, a workpiece is cut in its longitudinal direction.
• Position the longitudinal fence (5) on the left side
(if possible) of the saw band, in accordance with
the desired width.
Advertenties
