Advertenties
Quick Links
Advertenties
Gerelateerde Handleidingen voor HP LaserJet 4100 mfp Series
Samenvatting van Inhoud voor HP LaserJet 4100 mfp Series
- Pagina 2 FCC regulations The HP LaserJet 4100 mfp series has been tested and found to comply with First Edition, November 2001 the limits for a Class A digital device, pursuant to Part 15 of the FCC rules.
- Pagina 3 1040 mm HP LaserJet (41 inches) 4100 mfp 415 mm (16.4 inches) HP LaserJet 4100 mfp 540 mm (21.25 inches) HP LaserJet 4101 mfp 661 mm (26 inches)
- Pagina 4 3) Avlägsna plastfilmen som sitter på kontrollpanelens 5) Kontrollpanelens överdrag 6) Tonerkassett 7) Extra 500-arks teckenfönster. 4) Avlägsna allt förpackningsmaterial och eventuella pappersfack* 8) Enhet för dubbelsidig utskrift* distansbrickor från facken. *Medföljer HP LaserJet 4100 mfp och finns att få till HP LaserJet 4100 mfp...
- Pagina 5 3) Power/Jumper cable connectors 4) Rear output slot 5) Duplexer or dust numbers) 5) Tray 2 6) Tray 1 7) Toner cartridge access (under top cover) cover 6) Parallel interface port 7) Hard disk 8) HP Jetdirect print server 8) Control panel 9) Front output bin card 9) Fast InfraRed Connect (FIR port) 10) Memory access door Enheden (set forfra).
- Pagina 6 Unlock the scanner head. The scanner head is locked during shipping. Install the toner cartridge. 1) Remove the toner cartridge from its Before using the product, unlock the scanner head on the left side of the packaging. 2) Lift the top cover. product as you are facing it.
- Pagina 7 3) Pull the sealing tab tape from the end of the toner cartridge to remove Install accessories. Use the separate installation instructions to install the entire length of tape. Avoid touching any black toner on the tape. any accessories that you have purchased with the product. 1) Duplexer for 4) Slide the cartridge into the product as far as it can go.
- Pagina 8 Load paper Tray 2 and optional Trays 3 and 4. 1) Pull the tray 2) To adjust the width, squeeze the lever on the left guide and slide the completely out of the product. guides into place to match the media width. 3) To adjust the length, squeeze the lever on the back media guide and slide it to the desired media size until it clicks into place.
- Pagina 9 4) Squeeze the blue tab on the right side of the tray and move it to the Connect the power cord. 1) Locate the power switch on the right side of correct position based on the media size. 5) Slide the tray back into the the product.
- Pagina 10 4) Verify that the voltage supply you are using is within the range listed on Connect the cables. Use the RJ-45 port on the HP Jetdirect 610N print the electrical rating label located under the top cover of the product.
- Pagina 11 Turn the product on. Turn the power on and wait for the product to warm Set the control panel language. Choose the language from the available up. After the product warms up, the product prompts you to set the control options.
- Pagina 12 IP , remote configuration is preferred or more manually. (Note: Remote configuration can be performed, refer to support assistance is required, refer to support at www.hp.com.) at www.hp.com.) Angiv IP-adressen. Hvis du vil konfigurere MFP'en, skal du først angive Find e-mail-gateways.
- Pagina 13 Set the e-mail gateway addresses manually. 1) Select SMTP Test the digital sending function. 1) To verify that the product is GATEWAY, in the I/O menu and enter the gateway address. 2) Select connected to the network server, you can test the digital sending function LDAP GATEWAY, in the I/O menu and enter the gateway address.
- Pagina 14 Install the printing software (optional). Procedures for installing the Congratulations. You can now use the HP LaserJet 4100 mfp series for software vary according to operating system and network environment. printing, copying, color scanning, and digital sending. Refer to the Use guide, and follow the procedure that matches your system and environment.
- Pagina 16 © 2001 Hewlett-Packard Company http://www.hp.com/support/lj4100mfp *C9148 -90901 *C9148 -90901 C9148-90901...