Advertenties
Beschikbare talen
Beschikbare talen
10 | English
Additional perimeter wire can be added using a wire
connector (see figures D–E) .
The perimeter wire can be extended up to a maximum
length of 250 m .
The perimeter wire can be buried up to 5 cm under the
ground (or under non-metallic slabs) .
To avoid causing damage to the perimeter wire, do not
verticut or rake the area where it is positioned .
When laying out the wire avoid angles of less than 45° .
This can affect the performance .
Display
Symbol
Meaning
Back button
Confirm button
If the confirm button is pressed whilst
mowing, the mower will return to the
docking station
Red LED on: mower error
Green LED on: mower is switched on
Green LED off: The mower is inactive and
your four-digit PIN code is required for
activation .
Or the mower is shut off, the On/Off
switch must be turned on and your four
digit PIN code must be entered to activate
the mower .
Note: during a software update, the green
LED and red LED will be on .
Left/right button
Down/up button
Display with dialog screen
Garden number (shown when more than
1 2 3
one garden map in the mower memory)
Network signal present
Network signal absent
The display switches into sleep mode, if no input is made for
10 minutes .
Adding a further Garden/LawnArea
(see figure I)
To install the Miimo to an additional lawn area, please
follow the instructions in the Installation Guide .
Separate lawn area with separate docking station (see
figure I, right): The mower can be used on up to three
different lawns . For an additional lawn area, a separate
docking station (see figure A) and the necessary perimeter
wire and pegs are required . If a schedule or the Honda
"Smart Timer" calendar function is selected, it will cut the
grass of the area it is in, within the time slots .
Switch off the mower when transporting it between the
individual lawn areas .
Note: software updates have to be carried out on the
mower in every docking station .
To ensure remembering which docking station belongs
to which garden, it is recommended to label the docking
stations with the garden number and description when
storing them for winter .
Without separate docking station: It is possible to
connect the lawn areas by placing the perimeter wire
between the two lawn areas parallel to each other as
close as possible (see figure I, top left) . The additional
lawn area without docking station is not recorded in the
map memory and the mower will not use the Map & Mow
cutting strategy in this lawn area without the docking
station . The maximum recommended lawn area without
a docking station is 40 m
. The mower will mow until it
2
runs out of battery and will need to be carried back to the
docking station for charging .
Mowing
f Do not let children ride the mower .
f Press the stop button on top of the mower before
lifting . Always lift the mower by its handle . (see
figure F)
Make sure the cutting area is free of small animals such
as hedgehogs or tortoises .
After successful installation, you can begin mowing
immediately by pressing "mow" on the free Honda
Mii-monitor App . You could also set up a programmed
schedule, using the Honda "Smart Timer" functionality,
which can also plan future cutting sessions based on
when it is forecasted to rain .
A manual "calendar" can also be set up according to
your specific needs .
The mower must mow a lawn area 3 times completely
(do 3 full cuts) to learn the lawn area . During the learning
phase, the visual result may not be optimal .
Approximate runtimes for complete garden coverage
using Map & Mow are listed below . Please note that the
runtimes will vary depending on the lawn complexity and
number of objects within the garden .
100 m
4 h
2
350 m
12 h
2
400 m
14 h
2
Set a schedule with frequent repetitions . This achieves
good mowing results, the battery charge lasts longer and
you avoid clippings on the lawn .
Advertenties
Probleemoplossen
