Inhoudsopgave
Advertenties
In section 10 "Charger indicator" you will fi nd a
table with an explanation of the LED indicator on
the charger.
Important!
Only use the rechargeable battery and charger
when dry and with an ambient temperature of
10-40°C.
Store the rechargeable battery, cordless tool and
charger in a dry place with an ambient tempera-
ture of: Rechargeable battery = 10-20°C
Cordless tool, charger = 10-40°C.
If the battery pack fails to become charged, ple-
ase check
•
whether there is voltage at the socket-outlet
•
whether there is proper contact at the char-
ging contacts on the charger.
If the battery still fails to become charged, please
return
•
the charger
•
the battery pack
to our Customer Service Department.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
5.7 Battery capacity indicator
(Fig. 11 – Item h)
Press the battery capacity indicator switch (i). The
battery capacity indicator (h) shows the charge
status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
Anl_TP_PS_18_165_Li_BL_SPK13.indb 21
Anl_TP_PS_18_165_Li_BL_SPK13.indb 21
GB
1 LED blinks:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
6. Operation
6.1 Working with the plunge saw
•
Always grip the cordless plunge cut saw firm-
ly.
•
Do not any use force! Push the cordless
plunge cut saw forwards in a gentle and even
manner.
•
The waste piece should be on the right-hand
side of the cordless plunge cut saw so that
the wide section of the support bench sup-
ports its full area.
•
If you are sawing along a previously drawn
line, guide the cordless plunge cut saw along
the corresponding guide (see 5.5).
•
Clamp small pieces of wood securely before
sawing them. Never hold them with your
hand.
•
Always follow the safety instructions. Wear
safety goggles.
•
Do not use defective saw blades or blades
that are cracked or broken.
•
Do not use any flanges / flange nuts whose
bore hole is larger or smaller than those in the
saw blade.
•
The saw blade must not be decelerated by
hand or by applying lateral pressure to the
blade.
•
Before you use the machine, make sure that
the safety equipment such as the flanges and
adjustment devices are in working order and
are correctly adjusted and secured.
Warning!
Always remove the battery pack before making
adjustments to the equipment.
6.2 Using the plunge saw
•
Adjust the cutting depth, cutting angle and
parallel stop (see section 5.1, 5.2 and 5.4)
•
Do not switch on the plunge saw until you
- 21 -
08.10.2024 15:31:05
08.10.2024 15:31:05
Advertenties
Inhoudsopgave
