Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
6.4 Working (Fig. 7)
Press the trigger (Item 4) to close the cutting
blade, release the trigger to open it again to the
previously set opening width.
6.5 Switching off (Fig. 7-7a)
a) Press the trigger (Item 4) to close the cutting
blade. Hold the trigger and press the push
lock (Item 3) into the housing on the left. The
trigger (Item 4) will lock. After approx. 5 se-
conds the "ON-STANDBY-OFF" LED will light
up "Orange" (STANDBY Mode).
b) Press the function switch (Item 5a) for 3 se-
conds. A signal will sound, the "ON-STAND-
BY-OFF" LED will light up and the tool will be
switched off .
6.6 Finishing the job
Switch off the tool as described in Section 6.5,
remove the battery/batteries and fold the blade
guard cover over the branch cutting blade.
6.7 Belt clip
You can use the belt clip (Fig. 1 / Item 8) to hang
the tool on your belt for example. Both your hands
are then free and the tool is always within easy
reach. Danger! First switch the tool to at least
"Standby Mode".
Additional instructions
a) If the tool is ready for use and the trigger (Item
4) is not actuated for 30 seconds, the tool will
switch automatically from its current status
into STANDBY Mode. To restart the tool, pro-
ceed as described in the section "Switching
on".
b) The tool will switch off automatically after ap-
prox. 10 minutes in STANDBY Mode.
c) You can switch off the tool by pressing the
function switch (Item 5a) and continuing to
hold it.
d) Take account of the maximum cutting capa-
city (see Technical Data) when cutting bran-
ches.
e) If you try to cut branches that are too thick or
too hard for the tool to cut through, the cutting
blade will open automatically.
Anl_GP_LS_18_28_Li_BL_SPK13.indb 17
Anl_GP_LS_18_28_Li_BL_SPK13.indb 17
GB
7. Cleaning, maintenance and
ordering of spare parts
Hazard!
Always pull out the battery pack before starting
any cleaning work.
7.1 Cleaning
•
The blades must be cleaned with a soft brush
each time after use.
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
7.2 Maintenance
7.2.1 Lubricating the branch shears blade
(Fig. 8)
The branch shears blade must be lubricated each
time after it has been used and whenever requi-
red. Use universal oil spray or the ball pressure lu-
bricator (Item D) with a matching oil spraying can.
7.2.2 Resharpening the moving cutting blade
(Fig. 8)
If the cutting blade (Item 1) becomes blunt, you
can sharpen it yourself (Caution! Wear protective
gloves!) or have the blade replaced by the custo-
mer services team.
•
With the blade fully open, switch off the tool
and remove the battery.
•
Sharpen the cleaned cutting blade with a sui-
table grinding tool (e.g. a wet grinding stone,
wet grinding paper).
•
There are no other parts inside the tool which
require maintenance.
- 17 -
07.08.2024 14:39:35
07.08.2024 14:39:35
Advertenties
Inhoudsopgave
