Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Declaration of conformity
1. Information about the manufacturer
Name:
Truma Gerätetechnik GmbH & Co. KG
Address:
Wernher-von-Braun-Str. 12, D-85640 Putzbrunn
2. Appliance identification
Type / model:
LPG combination heater /
Combi 2 E*, Combi 4 (E)*, Combi 6 (E)*
* (UK) CP plus ready
3. Complies with the requirements of the following
EC directives
3.1 Gas appliances directive 2009/142/EC
3.2 Low-voltage directive 2006/95/EC
3.3 Heating systems UN ECE R122
3.4 Radio interference suppression in motor vehicles UN ECE R10
3.5 Electromagnetic compatibility 2004/108/EC
3.6 End-of-life vehicle directive 2000/53/EC
3.7 Drinking water directive 98/83/EEC
and bears the type approval numbers
Combi 2 E*: E1 10R–04 5020, E1 122R–00 0373
and the CE mark with the CE product identification number
CE-0085CN0021.
and bears the type approval numbers
Combi 4 (E)*: E1 10R–04 5020, E1 122R–00 0193
Combi 6 (E)*: E1 10R–04 5020, E1 122R–00 0194
and the CE mark with the CE product identification number
CE-0085BS0085.
* (UK) CP plus ready
4. Basis for the proof of conformity
EN 624:2011; EN 15033:2007; EN 60335-1:2010;
EN 60335-2-21:2009;
EN 60335-2-30:2002+A1:2004+A2:2007;
EN 55014-1:2006+A1:2009;
EN 55014-2:1997+A1:2001+A2:2008
5. Monitoring body
DVGW (German Technical and Scientific Association for Gas
and Water), Kraftfahrt-Bundesamt (Federal Motor Transport
Authority)
6. Signatory details
Frank Oster
Managing Director
Truma Manufacturer's Warranty
1. Warranty claims
The Manufacturer hereby warrants for all defects of the unit
caused by material or production faults. In addition, the seller
continues to be subject to any statutory warranty claims.
No warranty claim shall be applicable under the following
circumstances:
– Consumable parts which are subject to wear and tear
– Use of parts other than original Truma components in any
– In gas pressure regulation systems: damage caused by
– Failure to observe Truma's installation or operating
– Improper handling
– Improper transport packing
2. Scope of warranty
The warranty covers all defects under clause 1 that occur
within 24 months upon concluding the purchase agreement
between the seller and the end customer. The Manufacturer
undertakes to remedy such defects through subsequent fulfil-
ment, i.e. at its discretion either by repairing or replacing the
defective item. If the Manufacturer remedies a defect under
its warranty commitment, the term of the Warranty shall not
recommence anew with regard to the repaired or replaced
parts; rather, the original warranty period shall continue to be
applicable. No further-reaching claims shall be permitted, es-
pecially damage claims presented by purchasers or third par-
ties. This provision shall not affect the validity of the German
Product Liability Act (Produkthaftungsgesetz).
The Manufacturer shall bear the cost of employing the Truma
Customer Service for the removal of warranty defects – in
particular, transportation, travelling, job and material costs –
provided that the Customer Service conducts its work within
Germany. This Warranty does not cover Customer Service
work outside Germany.
Additional costs arising from complicated removal or instal-
lation jobs on the unit (e.g. dismantling of furnishings or parts
of the vehicle body) are not covered by the Warranty.
3. Making a claim under the warranty
The Manufacturer's address is:
Truma Gerätetechnik GmbH & Co. KG
Wernher-von-Braun-Straße 12
85640 Putzbrunn, Germany
Should problems occur, please contact the Truma Service Centre
or one of our authorised service partners (see www.truma.com).
Please describe your claim in detail and state the serial num-
ber of the unit and the date of purchase.
To help the Manufacturer determine whether your claim is
covered by the Warranty, the end user must take or send the
unit to the Manufacturer or service partner at their own risk.
In the event of damage to the heat exchanger, the gas press-
Putzbrunn, 06.05.2015
ure regulator, too, must be returned along with the unit.
Air conditioning systems:
To avoid transport damage, the unit must be sent either to the
Truma Service Centre in Germany or to the relevant authorised
service partner; this must only be done upon prior arrange-
ment. Otherwise the sender shall bear the risk for any trans-
port damage that may occur.
If a unit is sent to the manufacturing facility, make sure it is
shipped as a freight item. If the claim is covered by the War-
ranty, transport / shipping and the cost of return shall be
borne by the manufacturing facility. If the claim is not covered
by the Warranty, the Manufacturer shall notify the customer
to this effect, specifying the cost of repairs not borne by the
Manufacturer; shipping costs, too, shall be borne by the cus-
tomer in such a case.
of the units
foreign substances in the gas (e.g. oils, plasticisers)
instructions
19
Advertenties
Hoofdstukken
Inhoudsopgave
