VDP2301RGVLD10 - VDP2601RGYLD10 - VDP3801RGVLD10
•
Click on No File to remove the file from the list.
•
Click OK to save the settings.
•
When desired, a list of all DMX settings can be printed by clicking the Print button.
•
To save the configuration, click on Save Config. The file must be saved as CONFIG.DAT as this is the
file that will be loaded automatically by the laser projector.
•
Place the SD card back in the laser projector and switch the projector on. Make sure the SD CARD mode
switch [6] is pressed and the correct DMX address is set via the SD card controls.
6.3
PC controlled mode
•
The PC controlled mode uses the ILDA (International Laser Display Association) standard for control signal
and file formats. The laser projector must be connected to a suitable PC running appropriate software (e.g.
Pangolin, Mamba, Phoenix...). Refer to §5 for the cable layout of the ILDA cable. More on the ILDA standard
can be found on http://www.laserist.org/standards.htm.
Make sure to set the scan rate in the software equal to or lower than the actual scan rate of
the laser projector. Setting the scan rate too high may damage the laser projector; this
damage is not covered by the warranty.
•
Press the PC MODE switch [6] to select PC mode.
•
In this mode, the laser projector will receive its instructions and shows via the ILDA input port [10].
•
Multiple laser projectors can be linked via the ILDA THRU port [9].
7. Cleaning and Maintenance
•
All screws should be tightened and free of corrosion.
•
The housing, visible parts, mounting supports and the installation location (e.g. ceiling, suspension,
trussing) should not be deformed, modified or tampered with e.g. do not drill extra holes in mounting
supports, do not change the location of the connections.
•
Moving mechanic parts must not show any signs of wear and tear.
•
The electric power supply cables must not show any damage. Have a qualified technician maintain the
device.
•
Disconnect the device from the mains prior to maintenance activities.
•
Wipe the device regularly with a moist, lint-free cloth. Do not use alcohol or solvents.
•
There are no user-serviceable parts apart from the fuse.
•
Contact your dealer for spare parts if necessary.
8. Technical specifications
red
Laser colour
green
/power
purple
max. total output power
max. scan speed
optical angle
Power supply
Power consumption
Dimensions
Total Weight
Laser type
Laser class
Laser life
Use this device with original accessories only. Velleman nv cannot be held responsible in the event
of damage or injury resulted from (incorrect) use of this device. For more info concerning this
product and the latest version of this user manual, please visit our website www.hqpower.eu. The
information in this manual is subject to change without prior notice.
© COPYRIGHT NOTICE
The copyright to this manual is owned by Velleman nv. All worldwide rights reserved.
No part of this manual or may be copied, reproduced, translated or reduced to any electronic medium or otherwise without
the prior written consent of the copyright holder.
11/08/2011
VDP2301RGVLD10
663nm/160mW
533nm/100mW
408nm/200mW
460mW
20 Kpps
±20°
200 x 260 x 450mm
DPSSL (Diode Pumped Solid State Laser)
Class 3B
>5000h
IMPORTANT NOTE
VDP3801RGVLD10
665nm/215mW
533nm/85mW
405nm/200mW
500mW
20 Kpps
±20°
AC 110-240V 50/60Hz
300W
7.0kg
10
VDP2601RGYLD10
662nm/200mW
533nm/100mW
-
300mW
20 Kpps
±20°
200 x 260 x 310mm
±5.5kg
green: DPSSL
red: semiconductor laser diode
©Velleman nv