Advertenties
Beschikbare talen
Beschikbare talen
eng
Pneumatic hose pneumatic tools, 1.5 m long,
with quick couplings NW 7.2
Compressed air hose Ø 8 mm, 7 m long, with quick coupling
DN 5 (plug) and G ½" hose screw fi tting, for pressure testing
with compressed air
Compressed air hose Ø 8 mm, 1.5 m long, with quick coupling
DN 5 (plug, socket) for gas testing with compressed air
High-pressure hose Ø ½", 7 m long, with G ½" hose screw fi ttings,
with caps, for pressure testing of pipe systems
1" double nipple, for connecting 2 suction/pressure hoses
Fine fi lter with fi lter cartridge 90 µm
Fine fi lter cartridge 90 µm
Caps 1" with chain (REMS Multi-Push)
Plugs 1" with chain (suction/pressure hoses)
Plugs ½" with chain (REMS Multi-Push)
Caps ½" with chain (high-pressure hose)
Pressure gauge 6 MPa/60 bar /870 psi
Fine scaled pressure gauge 1.6 MPa/16 bar/232 psi,
Fine scaled pressure gauge 250 hPa/250 mbar/3.6 psi,
REMS CleanM
1.3 Applications
Device storage temperature
Water temperature
Ambient temperature
pH value
Smallest test volume
Compressor
Compressor
Operating pressure
Oil separation rate
Extraction rate
Compressed air vessel volume (Fig. 1 (35))
Condensation and particle fi lter
Flushing of pipe systems
Flushing of pipe systems
Flushing water connections
Water pressure pipe network
Water pressure when fl ushing with compressed air ≤ 0.7 MPa/7 bar/101 psi
Water fl ow rate
Pipe diameter installation
Pressure testing of drinking water installations
Pressure testing
f drinking water installations
Pressure test with compressed air
Reading accuracy < 200 mbar
Reading accuracy ≥ 200 mbar
Pressure test with water
Reading accuracy
Pressure testing of gas installations
Pressure testing of gas installations
Pressure test with compressed air
Reading accuracy < 200 mbar
Reading accuracy ≥ 200 mbar
1.4 Electrical/electronic data
Type of protection terminal box
Type of protection device, motor
Protection class
Operating mode (continuous operation)
Screen (LCD)
Resolution
Data transfer with USB stick
Printer, battery
Charger printer
1.5 Dimensions L × W × H
Paper roll printer B × Ø
1.6 Weight
REMS Multi-Push SL
REMS Multi-Push SLW
1.7 Noise information
Work place-related
Emission value
2 Start-up
CAUTION
CAUTION
Transport weights above 35 kg must be carried by at least 2 persons.
Compressed air line compressor/pressure vessel (47) gets hot and can cause
burns if touched.
NOTICE
REMS Multi-Push is not intended/suitable for permanent connection to the
installation. Disconnect all hoses from the installation after completing the work.
REMS Multi-Push may not be operated unattended.
5°C – 35°C
5°C – 40°C
approx. 10 l
≤ 0.8 MPa/8 bar/116 psi
≤ 230 Nl/min
≤ 1 MPa/10 bar/145 psi
≤ DN 50, 2"
≤ 0.4 MPa/4 bar/58 psi
1 hPa/1 mbar/0.015 psi
100 hPa/0,1 bar/1.5 psi
≤ 1.8 MPa/18 ba r/261 psi
0.02 MPa/0.2 bar/3 psi
≤ 0.3 MPa/3 bar/44 psi
10 Pa/0,1 mbar/0.002 psi
100 hPa/0,1 bar/1.5 psi
230 V~; 50 Hz; 1,500 W
110 V~; 50 Hz; 1,500 W
128 × 64 pixels
Ni-Mh 6 V – ---; 800 mAh
Input
100 – 240 V~; 50 – 60 Hz; 0.15 A
5 V – ---; 680 mA
Output
570 × 370 × 530 mm (22.4" × 14.6" × 20.9")
57 × ≤ 33 mm
36.7 kg (81 lb)
39.0 kg (86 lb)
L
= 73 dB(A); L
= 73 dB(A); L
= 73 dB(A); L = 92 dB(A); K = ± 1 dB(A)
= 73 dB(A); L
PA
PA
PA
WA
WA
2.1 Electrical connection
115621
WARNING
Caution: Mains voltage present! Before connecting the electronic fl ushing and
pressure testing unit, check whether the voltage given on the rating plate corre-
115667
sponds to the mains voltage. Only use sockets/extension leads with a functioning
PE contact. The function of the PRCD fault current circuit breaker (Fig. 1 (1))
115747
must be checked every time before start-up and before beginning work:
115661
1. Plug the mains plug into the socket.
045159
2. Press the RESET button (2), the PRCD control lamp (Fig. 1 (39)) lights red
115609
(operating state).
043054
3. Pull out the mains plug, the PRCD control lamp (39) must go out.
115619
4. Plug the mains plug back into the socket.
115620
5. Press the RESET button (2), the PRCD control lamp (39) lights red (oper-
ating state).
115624
6. Press the TEST button (3), the PRCD control lamp (39) must go out.
115623
7. Press the RESET button (2) again, the PRCD control lamp (39) lights red.
115140
The control lamp (Fig. 2 (5)) lights green. REMS Multi-Push is ready for
115045
operation after about 10 s.
047069
140119
WARNING
If the described functions of the PRCD fault current circuit breaker (Fig. 1 (1))
≥ 5°C
are not fulfi lled, the device may not be used. There is a danger of electric shock.
The PRCD fault current circuit breaker tests the connected device, not the
installation before the socket nor interconnected extension leads or cable reels.
6,5 – 9,5
On building sites, in a wet environment, indoors and outdoors or under similar
installation conditions, only operate the electronic fl ushing and pressure testing
unit on the mains with a fault current protection switch (FI switch) which interrupts
the power supply as soon as the leakage current to earth exceeds 30 mA for
200 ms. A cable cross-section that corresponds to the power of the electronic
oil-free
fl ushing and pressure testing unit must be selected when using an extension
lead.
4.9 l
5 µm
Flushing
Ingredients
DN 25, 1"
Testing
Compressed Air Pump
≤ 5 m³/h
Memory Manager
Press the On/Off button on the input and control unit's operating panel (Fig. 2
(4)) for approx. 2 s, then release it. REMS Multi-Push is switched on and the
compressor switches on. The screen (6) is illuminated and the Logo REMS
Multi-Push logo appears followed by the Start menu:
2.2 Menu structure and on-screen displays
Five main programs of the REMS Multi-Push are displayed in the Start menu:
Flushing, Ingredients, Testing, Compressed Air Pump, Memory Manager. The
screen display contains a maximum 5 lines with 20 characters each. Lines with
defaults or test values are displayed language-independently with physical
formula symbols, a uniform verbal abbreviation and the value of the test crite-
rion in the sub-routines. These have the following meanings:
p refer
bar xxx
p refer
mbar xxx
IP 44
p actual bar xxx
p actual mbar xxx
IP 20
p diff
bar xxx
I
p diff
mbar xxx
S 1
t stabi
min xxx
3.0"
t test
min xxx
Δ > 10K
USB port
PfS
P+M
p H
O
bar
2
v H
O
m/s
2
t H
O
min
2
n H
O
n-times
2
VA H
O l
2
VS H
O l/min
2
V H
O
l
2
File no.
max. DN
Enter
Esc
Ver. Software
2.3 Settings menu
NOTICE
The defaults for the different test criteria in the Settings menu of the REMS
Multi-Push are taken from the EN 806-4:2010 or the information leafl et "Leak
tests of drinking water installations with compressed air, inert gas or water"
(January 2011) of the German Central Association for Sanitary, Heating and
Air Conditioning (ZVSHK) as well as the Technical Rule "Technical Rule for
Gas Installations Worksheet G 600 April 2008 DVGW-TRGI 2008" of the DVGW
German Gas and Water Association. All defaults for the test programs can be
edited by the user in the Settings menu and in the Flushing, Test with compressed
air, Test with water and Compressed Air Pump programs
Settings menu are saved, i.e. they reappear the next time the REMS Multi-Push
reference test pressure
bar
reference test pressure
mbar
actual test pressure
bar
actual test pressure
mbar
differential test pressure bar
differential test pressure mbar
stabilisation/wait time
min
test time
min
difference >10°C (10 Kelvin) water/environment
press fi tting system (ZVSHK)
load test plastic + metal
water pressure
minimum fl ow speed
fl ushing/disinfecting/cleaning/preservation time
water change
volume of the fl ushing section
volume fl ow
used water volume
memory location no. for measuring log
largest rated diameter
next screen display
previous screen display or cancel
version software
programs. Changes in the
eng
21
Advertenties
