General Information - Novy 6830 Installatievoorschriften
Verberg thumbnails
Zie ook voor 6830:
- Gebruiksaanwijzing en installatievoorschriften (25 pagina's) ,
- Installatievoorschriften (12 pagina's)
Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
GENERAL INFORMATION
General
These are the mounting instructions for the Novy hood shown on the cover. The manual is a separate booklet that
has been supplied with this hood. Read these instructions carefully before installing and commissioning the hood. It is
recommended to have one or more qualified persons carry out the installation.
Carefully take the hood from the packaging. Check if all mounting materials have been supplied using the drawings on
page 2.
The hood is to be used above a cooking plate and/or domino and it is intended for household use only. The built-in unit
is to be placed in a self-constructed recessed housing.
The recommended minimum overall height is: 60 cm over an electrical/ceramic cooking plate, 65 cm over a gas or an
induction cooking plate. The recessed housing must at least fully bridge the cooking plate. The built-in unit is preferably
mounted centralised over the cooking zones.
Important before mounting
Page 2 of these mounting instructions show the mounting drawings. Observe the following mounting tips before starting
the mounting activities:
• For easier mounting of the ceiling unit, it is recommended to do this with at least 2 persons.
• Position the wall socket in such a way that it is behind the ceiling unit.
• Make sure that the ceiling has sufficient load bearing capacity.
• Remove the protective film from the stainless steel parts of the ceiling unit before mounting. Avoid damaging the
stainless steel.
Exhaust or recirculation
Before starting any mounting activities, you must have made the choice if you are going to make an exhaust duct to the
outside or if you are going to use the hood as a recirculation hood. In case of an exhaust duct to the outside, carefully
read the section in these mounting instructions for installing the exhaust duct. If you choose for recirculation, Novy offers
the exhaust box (see accessories).
InTouch
InTouch offers the option to control the Novy cooker hood from the Novy InTouch induction hotplate. The ceiling unit
may, as a default, be combined with InTouch induction hotplates. Visit the website for the different models of induction
hotplates with InTouch
INSTALLATION
Proceed following the mounting drawings on page 2 and 3.
Make a build-in opening:
1
Type 6830 / 6831 – Cut-away 845mm x 485mm.
Type 6840 / 6841 – Cut-away 1145mm x 485mm.
The ceiling unit can be built into plates with a thickness of 18-35mm. Do not mount directly into gypsum board; al-
ways make sure there is reinforcement for the tightening of the mounting clamps. Make sure there is a socket near
the ceiling unit, so that the power may, at all times, be removed from the ceiling unit.
Changing the exhaust direction of the motor (if desired).
2
Sideways:
- Open the bottom plate and remove the filters from the ceiling unit.
- Disconnect the cord that connects the motor to the ceiling unit.
- Loosen the 8 screws located next to the protective grid.
- Turn the motor with the exhaust into the desired position and screw the motor back on using the 8 screws.
Changing the exhaust direction of the motor (if desired).
3
Top:
A Loosen the 6 screws on the motor cover.
B Turn the motor cover a quarter turn and place the motor cover back into the motor housing. Screw it back on again
using the 6 screws.
Connect the exhaust duct to the connection nozzle by means of a hose clamp (keep in mind the length of the exhaust
4
duct in case of removal, if necessary).
Put the plug into the wall socket.
Push the ceiling unit up into the build-in opening by pushing on the edges (not on the bottom plate) until you hear a
EN 13
Advertenties
Inhoudsopgave
