Advertenties
Beschikbare talen
Beschikbare talen
EN
holding the handle lock button again,
Open the water tank cover and fi ll in the tank with water. Close the tank cover. Place the iron upright resting it on the back wall and
check that the water level is not higher than the "MAX" indicator on the water tank. Place the iron in a vertical position, resting it
on the back wall and plug the power cord into the socket.
Move the temperature controller to the "max" position. The power indicator lights up and the soleplate heats up. The end of the
heating up will be signalled by the power indicator going off . When the iron is heated up for the fi rst time, unpleasant smells, small
amounts of smoke and small particles can come out of the iron.
After heating up is fi nished, hold the iron by the handle. Set the steam controller to a maximum (shifted to the front of the iron as
far as possible) and press the steam boost button several times while holding the iron horizontally. All settlements will be removed
from the steam delivery system.
The fi rst ironing is recommended to be carried out on a cloth so as to make sure that the iron's soleplate does not mess the ironed
fabrics.
After the preparation is complete, start ironing or place the iron in a vertical position, resting it on the back wall, unplug the power
cord from the socket and allow the iron's soleplate to cool down on its own.
Filling in and emptying the water tank
Warning! Before fi lling in or emptying the tank, make sure the power cord plug is disconnected from the power supply socket and
that the iron's soleplate is not hot.
Open the water tank cover and fi ll in the tank with water. Close the tank cover. Place the iron upright resting it on the back wall
and check that the water level is not higher than the "MAX" indicator on the water tank. Never fi ll in the tank so that the water level
is higher than the indicator level.
The iron is designed for use of tap water. However, if the water contains a large amount of limescale, use a 1:1 mix of tap water
with demineralised or distilled water or just demineralised or distilled water.
This will extend the lifetime of the iron and reduce or prevent limescale build-up inside the steam system of the iron. Contact your
water supplier for water parameters.
The iron tank should be emptied after each use. Open the tank cover and turn the iron so that the fi lling opening faces downwards.
Hold the iron in this position until the water is completely removed.
Caution! Even after the tank has been emptied completely, a small amount of water remains in the steam system.
Setting the ironing temperature
The ironing temperature can be set by turning the knob. The line embossed on the transparent knob cover should be used as a
marker for the knob adjustment. The knob has the following settings (given from the lowest to the highest temperature):
"off " - turning off the soleplate's heater. Do not treat this position as the off switch of the iron. The iron is only switched off when
the power cord is unplugged.
"min." - turning on the soleplate's heater and maintaining a minimum temperature.
"silk / *" - this temperature setting allows to iron delicate fabrics such as silk, artifi cial silk, synthetic fabrics.
"wool / **" - temperature setting that allows to iron fabrics such as wool.
"cotton / ***" - temperature setting that allows to iron fabrics such as cotton.
"max / linen" - the highest temperature setting that allows to iron fabrics such as linen.
The heater operation is indicated by the power indicator lighting up. The iron's thermostat automatically maintains the temperature
set by the knob, turning on and off the heater. The frequency of the heater switching on depends on the ambient temperature
and the temperature set by the knob. The lower the ambient temperature and the higher the set temperature, the more often the
heater will be switched on.
If a lower temperature is set after ironing at a higher temperature, allow the iron's soleplate to cool down on its own. Wait until the
power indicator lights up. Cooling down can only be accelerated by starting a steam boost. It is forbidden to accelerate the cooling
down in any other way, e.g. by immersing the soleplate in water.
Dry ironing
You can iron dry with this iron. There is no need to pour water into the iron's tank. However, if the water is already in the iron, there
is no need to pour it out. The steam controller must be set to the minimum position as far as it will go.
The steam boost button functions are inactive when the steam controller is in its minimum position.
Steam ironing
Fill in the tank with water. Set the steam controller to a position other than the minimum position. Set the temperature knob to "max
/ linen" position. Start heating up. During ironing, water vapour will be extracted through the holes in the iron's soleplate with the
intensity set by the steam controller.
If even more steam is required, press the steam boost button. Do not press the button more than three times in a row. For best
performance, it is recommended to follow breaks of at least 4 seconds between successive presses of the steam boost button.
When the steam chamber is emptied, the iron needs some time to refi ll it. Pressing the steam boost button during this time will
O R I G I N A L
I N S T R U C T I O N S
12
Advertenties
