Inhoudsopgave
Advertenties
2 Installation location
A
Fig 2-1
Installing the outdoor unit
A
M10 (3/8") bolt
B
Base
C
As long as possible.
D
Vent
E
Set deep in the ground
600
Min.475
225
Min.25
Fig
4 Installing the re rigerant piping
All manuals and user guides at all-guides.com
B
Fig 2-1
(mm)
D
600
225
1050
-1
2
ind location installation
wind, situate the air outlet of the unit so that it is not directly exposed to strong winds.
may result.
The following shows two examples of precautions against strong winds.
1 Install an optional air guide if the unit is installed in a location where strong winds
from a typhoon, etc. may directly enter the air outlet. (Fig. 2-15)
A Air guide
2 Position the unit so that the air outlet blows perpendicularly to the seasonal wind
direction, if possible. (Fig. 2-16)
B
operation. (Fig. 3-1)
Foundation bolt
Thickness of concrete
120 mm
Length of bolt
of the base.
Installing the outdoor unit
down may result.
wires, etc., if necessary to install the unit. Use self-tapping screws (ø5
less) and install on site.
arning
The unit
ust e securel installed on a structure that can sustain its weight
I the unit is
ounted on an unsta le structure it
da age or in uries
The unit
ust e installed according to the instructions in order to
the ris o da age ro
earth ua es t phoons or strong winds An incor-
rectl installed unit
a
all down and cause da age or in uries
4 1 Precautions or de ices that use R410A re rigerant
Re er to page
or precautions not included elow on using air conditioners
with R410A re rigerant
Use ester oil ether oil al
l en ene oil s all a ount as the re rigeration
oil applied to the ared sections
Use C1220 copper phosphorus or copper and copper allo sea less pipes
to connect the re rigerant pipes Use re rigerant pipes with the thic nesses
speci ed in the ta le to the elow Ma e sure the insides o the pipes are clean
and do not contain an har
ul conta inants such as sul uric co pounds
o idants de ris or dust
arning
hen installing or relocating or ser icing the air conditioner use onl the
speci ed re rigerant R410A to charge the re rigerant lines Do not
an other re rigerant and do not allow air to re ain in the lines
I air is
i ed with the re rigerant then it can e the cause o a nor al high
pressure in the re rigerant line and
The use o an re rigerant other than that speci ed or the s ste
echanical ailure or s ste
al unction or unit rea down In the worst case
this could lead to a serious i pedi ent to securing product sa et
[6.35
[9.52
Pipe size (mm)
Thickness (mm)
0.8
0.8
Do not use pipes thinner than those speci ed a o e
Use 1 2 H or H pipes i the dia eter is 1 0
70 mm
320 kg
15 mm or
a
all down and cause
ini i e
i it with
a result in an e plosion and other ha ards
will cause
[12.7
[15.88
[19.05
[22.2
0.8
1.0
1.0
1.0
or larger
-
Advertenties
Hoofdstukken
Inhoudsopgave
Gerelateerde Handleidingen voor Mitsubishi Electric CITY MULTI PUMY-P200YKM
Gerelateerde Producten voor Mitsubishi Electric CITY MULTI PUMY-P200YKM
- Mitsubishi Electric CITY MULTI PUMY-P112VKM5
- Mitsubishi Electric CITY MULTI PUMY-P125VKM5
- Mitsubishi Electric CITY MULTI PUMY-P140VKM5
- Mitsubishi Electric CITY MULTI PUMY-P112VKM5-ET
- Mitsubishi Electric CITY MULTI PUMY-P125VKM5-ET
- Mitsubishi Electric CITY MULTI PUMY-P140VKM5-ET
- Mitsubishi Electric CITY MULTI PUMY-P112YKM5
- Mitsubishi Electric CITY MULTI PUMY-P125YKM5
- Mitsubishi Electric CITY MULTI PUMY-P140YKM5
- Mitsubishi Electric CITY MULTI PUMY-P112YKM5-ET
- Mitsubishi Electric CITY MULTI PUMY-P125YKM5-ET
- Mitsubishi Electric CITY MULTI PUMY-P140YKM5-ET
- Mitsubishi Electric CITY MULTI PUMY-P112YKME4
- Mitsubishi Electric CITY MULTI PUMY-P125YKME4
- Mitsubishi Electric CITY MULTI PUMY-P140YKME4
- Mitsubishi Electric CITY MULTI PUMY-P200YKM2