Advertenties
8. Unpacking
• Open the packaging and carefully remove the device.
• Remove the packaging material, as well as the pack-
aging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport
damage. In the event of complaints the carrier must
be informed immediately. Later claims will not be
recognised.
• If possible, keep the packaging until the expiry of the
warranty period.
• Familiarise yourself with the product by means of the
operating instructions before using for the first time.
• With accessories as well as wearing parts and re-
placement parts use only original parts. Replace-
ment parts can be obtained from your dealer.
• When ordering please provide our article number as
well as type and year of manufacture for your equip-
ment.
m WARNING!
The device and the packaging material are not
children's toys! Do not let children play with plas-
tic bags, films or small parts! There is a danger of
choking or suffocating!
9.
Before commissioning
• Before connecting the machine, make certain that
the data on the type plate matches with the mains
power data.
• Check the device for transport damage. Report any
damage immediately to the transport company which
was used to deliver the compressor.
• Install the compressor near the point of consumption.
• Avoid long air lines and supply lines (extension cables).
• Make sure that the intake air is dry and free of dust.
• Do not install the compressor in a damp or wet room.
• The compressor may only be used in suitable rooms
(with good ventilation and an ambient temperature
from +5 °C to 40 °C). There must be no dust, acids,
vapours, explosive gases or inflammable gases in
the room.
• The compressor is designed to be used in dry rooms.
It is prohibited to use the compressor in areas where
work is conducted with sprayed water.
• The compressor may only be used outdoor briefly
when the ambient conditions are dry.
• The compressor must always be kept dry and must
not be left outdoors after work is complete.
24 | GB
10. Attachment and operation
m Attention!
Always make sure the device is fully assembled
before commissioning!
You require the following for assembly:
2 x open-ended wrench size 14 mm and 17 mm
(not included in the scope of delivery)
10.1 Fitting the wheels (fig. 6, 7)
• Insert the wheel bolt (d) through the wheel (3) and
slide on a washer (e) with the bolt (d). Now feed the
wheel bolt (d) through the hole provided on the com-
pressor. Slide the washer (c) and the spring washer
(f) onto the bolt and secure the wheel with the hex-
agonal nut (g).
10.2 Fitting the foot (fig. 5)
• Slide the hexagonal screw (a) through the foot (4).
Fit a washer (c) between the compressor and the
foot (4). Now feed the combination through the hole
provided and secure the screw (a) with a washer (c)
and nut (b).
• Carry out the same procedure with the second foot
(4).
10.3 Fitting the air filter (fig. 8)
• Remove the transport lid and screw the air filter (13)
to the equipment.
10.4 Mains connection
• The compressor is equipped with a mains cable with
protective contact plug. This can be connected to
any 220 ‒ 240 V∼ 50 Hz protective contact socket,
with fuse protection of at least 16 A.
• Before you use the machine, make sure that the
mains voltage is the same as the operating voltage
and the machine power on the rating plate.
• Long supply cables, extensions, cable reels, etc. cause
a drop in voltage and can impede motor start-up.
• At low temperatures below +5 °C, sluggishness may
make starting difficult or impossible.
10.5 On/off switch (fig. 1)
• Pull the on/off switch (8) upwards to switch on the
compressor.
• Press the on/off switch 8) down to switch off.
www.scheppach.com
Advertenties
