Advertenties
•
Do not add fuel to the engine in an indoor area. Not
sufficient airflow can cause injury or death because
of asphyxiation or carbon monoxide.
•
Tighten the fuel tank cap fully. If the fuel tank cap is
not tightened, there is a risk of fire.
•
Move the product a minimum of 3 m / 10 ft from the
position where you filled the tank before a start.
•
Do not fill the fuel tank fully. Heat causes the fuel to
expand. Keep a space at the top of the fuel tank.
•
Never store the product with fuel in the fuel tank
inside a building where ignition sources are present
such as hot water heaters, space heaters or clothes
dryers. Allow the engine to cool Before storing in any
enclosure.
Safety instructions for maintenance
WARNING:
instructions that follow before you use the
product.
•
The exhaust fumes from the engine contain carbon
monoxide, an odourless, poisonous and very
Introduction
WARNING:
product, you must read and understand the
safety chapter.
WARNING:
cable from the spark plug before you
assemble the product.
To assemble the handle
1. Loosen the lower knobs on the left and the right side
of the product. Make sure that the plastic washer is
in the recess in the handle bracket. (Fig. 30)
2. Install the handle folded forward as shown in the
illustration. (Fig. 31)
a) Make sure that the plastic washer is between the
handle and the handle bracket.
b) Attach the handle to the handle bracket.
3. Lift the handle up. (Fig. 32)
4. Tighten the knobs fully. To adjust the handle height,
To adjust the handle height on page 12 .
refer to
5. Put the wires in the cable brackets. Make sure that
the wires are not twisted. Attach the cable brackets
to the handle. (Fig. 33)
6. Use a cable tie to attach the cables to the handle
bracket. (Fig. 34)
12
Read the warning
Assembly
Before you assemble the
Remove the spark plug
dangerous gas. Do not start the engine indoors or
in closed spaces.
•
Before you do the maintenance on the product, stop
the engine and remove the ignition cable from the
spark plug.
•
Use protective gloves when you do maintenance on
the cutting equipment. The blade is very sharp and
cuts can easily occur.
•
Accessories and changes to the product that are
not approved by the manufacturer, can cause
serious injury or death. Do not change the product.
Always use accessories that are approved by the
manufacturer.
•
If the maintenance is not done correctly and
regularly, the risk of injury and damage to the
product increases.
•
Only do the maintenance as given in this owner's
manual. All other servicing must be done by an
approved Husqvarna service agent.
•
Let an approved Husqvarna service agent do
servicing on the product regularly.
•
Replace damaged, worn or broken parts.
To adjust the handle height
1. Loosen the lower knobs.
2. Move the knobs to the lower end of the grooves on
the left and the right side of the product. (Fig. 35)
3. Set the handle height in 1 of the 2 available
positions.
4. Move the knobs up in the direction of the handlebar
until they stop and you hear a click. (Fig. 36)
5. Tighten the knobs fully.
To set the product in transport position
1. Remove the grass catcher.
2. Loosen the lower knobs.
3. Move the knobs to the lower end of the grooves on
the left and the right side of the product. (Fig. 35)
4. Fold the handle forward. (Fig. 37)
To set the product in operation position
1. Lift the handlebar up. (Fig. 32)
2. Move the knobs up in the direction of the handlebar
until they stop and you hear a click. (Fig. 36)
3. Tighten the knobs fully.
To assemble the grass catcher
1. Attach the grass catcher frame to the grass bag with
the rigid part of the bag on the bottom. Keep the
handle of the frame on top of the grass bag. (Fig. 38)
1906 - 007 -
Advertenties
