Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
b
ark mode:
10 sec. bark
c
hime mode: 2x "ding-dong"
s
iren mode:
20 sec. siren
Deleting all the wireless components (e.g. if the remote control is lost):
!
Deactivate the EW01 by pressing the button [10] or [16] once. The LED
[5] goes out.
!
Press and hold the "LEARN" button [8] for approximately 20 seconds
until you hear a long beep first of all and two beeps (one long, one short)
later on as confirmation. All the wireless components are now deleted.
11. Power LED and battery change
M
ain unit
W
hen the main unit is switched on, the status of the power supply is
indicated by the colour of the Power LED 6 :
l
ights green:
p
ower via mains adapter atteries are OK
l
ights orange:
p
ower via mains adapter
batteries change batteries if these are fitted - batteries are
(
optional for back up - see Chapter 7, point 4)
l
ights red:
n
o power via mains adapter
(
change batteries - see Chapter 7, point 4)
D
oes not light: no power via mains adapter ither power by batteries, or
if the batteries are not fitted or are weak no power.
R
emote control
I
f the indicator 15 does not illuminate or illuminates weak when a button is
[ ]
pressed and / or the transmitting range becomes shorter then the battery
must be replaced (3 V battery CR 2032, see chapter 7, points 1 to 3)
1 . Fault finding
5
Fault
N
o reaction to movement
U
nit does not react to the remote control
T
ransmitting distance of remote control is
very short
U
nwanted triggering of main unit
[ ]
/ b
/ n
o batteries fitted or weak
/ p
ower via weak batteries
/ e
Cause
S
ensor range too low
Unit is facing in the wrong direction
Thick wall
, glass
or metal object is blocking the sen or
N
o wireless connect on
i
C
ode has been lost
B
attery is weak
M
ovement of animals or passing cars
H
eat sources can trigger the unit
Electrical wiring in the wall can trigger the unit, F
to microwave ovens, wireless surveillance cameras or
WLAN routers
U
nit is operating on weak batteries (power LED
illuminates red
)
1
2. Maintenance + cleaning
#
You should regularly check the device to see that it is safe and working
properly.
#
Before you clean the device, pull the mains adapter out of the mains
socket.
#
Use a dry or slightly moist cloth for cleaning the device.
#
Never immerse the device in water.
#
Do not use solvents to clean the device.
1
3. implified EU eclaration of onformity
S
Hereby,
INDEXA GmbH declares that the adio
compliance with
Directive 2014/53/EU. The full text of the EU eclaration of
c
onformity is available at the following nternet address:
https://www.indexa.de/ce.htm
1
4. Disposal
P
ackaging material, used batteries or electrical products must not be
disposed of as household waste. Use your recycling system. Details
are available from your local authority.
Indexa GmbH, Paul-Böhringer-Str. 3, 74229 Oedheim, Germany
Remedy
Set adjuster 3 higher
B
ack side of unit must face the area to be monitored
C
hange the location of the unit or use a radio motion detector
s
MA80P in a suitable location outside
R
educe the distance between remote control and unit
E
nroll the remote control to the unit again (see chapter 10)
R
eplace the battery (see chapter 10)
R
educe the range of the sensor using adjuster 3
C
hange the location of the unit
S
witch off the heat sorces or change the location of the unit
Change the location of the unit
aults due
R
enew the batteries (see chapter 7, point 4)
[6]
d
c
r
equipment type EW01 is in
i
.
www.pentatech.de Subject to change
[ ]
[ ]
d
GB - 21
Advertenties
Hoofdstukken
Inhoudsopgave
