Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Setting the groove depth
This function allows you to cut grooves into the work piece. The
work piece is only cut to a certain (set) depth and is not cut
through.
Groove cutting poses an increased risk of injury since
the saw head may bounce upward. Do not exert any
lateral pressure on the saw blade. Firmly secure the
work piece with the vise assembly.
Set the saw head and rotary table to the desired position
and lock it in place.
If you turn in the adjusting screw (33), the saw head lifts
up → flatter groove.
If you unscrew the adjusting screw (33), the saw head
lowers → deeper groove.
Firmly secure the work piece with the vise assembly
(19).
The groove is cut over the whole length if you place a
stop attachment between work piece and work piece
stop.
Cut the work piece as described at "Straight cuts".
Maintenance and cleaning
Before each maintenance and cleaning
work
Switch off device.
Wait for standstill of the saw blade
Pull out power plug
Maintenance and repair work other than those described in this
chapter is only allowed to be carried out by service staff.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Only use genuine spare parts. Other than genuine parts may
result in unpredictable damages and injury.
Cleaning
Observe the following to maintain the functionality of the
saw.
Do not wash down device with water.
Remove splints and sawdust only with a brush or vacuum
cleaner.
Clean and oil all moving parts regularly.
Never use any grease!
Use for instance sewing machine oil, liquid hydraulic
fluid or environmentally acceptable spray oil.
Take care that the saw blade remains free of rust and resin.
Remove resin residues from the surface of the rotary table.
Resin residues can be removed with a commercial
maintenance and care spray.
The saw blade is a wearing part and will become dull after
prolonged or frequent use.
Replace the saw blade in that case.
19
Thoroughly shake out the dust bag. Wash the dust bag in
case of heavy soiling but at least once a year with a mild
soap solution.
Maintenance
Changing the saw blade
Danger of cutting! Wear gloves when replacing the saw
blade.
Use only suitable saw blades.
Danger of burning! The saw blade is still hot shortly
after cutting.
Secure the pulling mechanism.
Place the saw head to the top position.
Swing the pendulum cover (16) upward until the screw (A)
is exposed.
Loosen the screw (A).
Swing the holding plate for the pendulum cover (16A) and
the pendulum cover (16) up.
Push the saw blade locking device (39).
Slowly turn the saw blade by hand until the saw blade
locking device catches. Keep the saw blade locking device
pressed.
Unscrew the hexagonal screw (35) for the saw blade using
the supplied tool (42).
Left-hand thread!
You can now remove the front saw blade flange (36),
the saw blade (37), the reducing washer (B) and the rear
saw blade flange (38).
Clean the saw blade flanges and the reducing
Put the rear saw blade flang and the reducing washer
on the shaft again.
Insert a new saw blade.
Pay attention to the correct running direction of
the saw blade: The arrow on the saw blade and
the arrow on the protective cover must point in
the same direction!
Reinstall the front saw blade flange and the washer (B).
The further assembly is now done in reverse sequence.
Retighten the hexagon screw.
Check the pendulum cover for its correct functioning before
proceeding.
Replacing the carbon brushes
Replace the carbon brushes once they have been worn
down to approx. 4 mm.
Remove the carbon brush cover (4) on the side of the
motor cover by turning it counterclockwise using a suitable
screw driver.
Remove the carbon brush (42); note the position of the
spring retention.
Insert the new carbon brushes observing the correct posi-
tion of the spring retention.
Replace the carbon brushes only in pairs.
Screw in the carbon brush cover again.
washer.
Advertenties
Hoofdstukken
Inhoudsopgave
