Start Charging; Stop Charging; Requirements Installation Space - Webasto Pure Bedienings- En Montagehandleiding
Verberg thumbnails
Zie ook voor Pure:
- Bedieningshandleiding (13 pagina's) ,
- Bedienings- en installatiehandleiding (10 pagina's) ,
- Bedienings- en montagehandleiding (11 pagina's)
Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
4.5 Start charging
Always take into account the vehicle requirements
before charging a vehicle.
Park the vehicle for charging such as to avoid strain in
the charging cable. See Fig. 06.
Action
Description
Connect the charging
Charging station performs
X
X
coupling to the vehicle.
system and connection tests.
LED: is blue, turns red for
about 2 seconds after
connecting to the vehicle
and then either turns green
(vehicle is charging) or flashes
blue (vehicle not yet ready for
charging)
4.6 Stop charging
Action
Description
The vehicle has stopped
LED flashes blue at 1 second
the charging cycle auto-
intervals. Vehicle connected,
matically:
not charging.
Unlock the car if
X
X
necessary.
Unplug the charging
X
X
coupling from the
vehicle.
Lock charging coupling
X
X
in the holder of the
charging station.
Action
Description
If the vehicle does not
automatically stop the
charging cycle:
Set key-operated
Charging cycle is stopped.
X
X
switch to "Off"
LED changes to blue and
position.
flashes at 5 second intervals.
See Fig. „05" - operating
status N5.
6
Action
Description
Or
Stop charging cycle at
Charging cycle is stopped.
X
X
vehicle.
LED changes to blue and
flashes at 1 second intervals.
See Fig. „05" - operating
status N4.
5 Transportation and storage
Acclimatization:
Do not open the scope of delivery if the temperature
difference between transportation and installation
location is more than 15 °C. To acclimatise the char-
ging station leave it unopened for at least 2 hours to
prevent condensation forming in the station.
Observe the ambient temperature for storage during trans-
portation. See chapter „13.1 Technical data".
Transport the charging station only when suitably pa-
ckaged.
6 Scope of delivery
Fig.
Description
11
Charging station with pre-assembled charging
cable
04
Mounting frame
2 keys
The installation kit for wall mounting consists of:
■
■
4 wall plugs (8 x 50 mm, Fischer UX R 8)
■
■
2 screws (6 x 70, T25)
■
■
2 screws (6 x 90, T25)
■
■
4 washers (ISO 7089-8.4)
Documentation
Take the charging station and the mounting frame from
X
X
the package.
Check the completeness of the delivery.
X
X
Check the complete delivery for damage.
X
X
7 Required tools
Tool description
Slot-head screwdriver 0.5x3.5 mm
Torx screwdriver Tx25
Torx screwdriver Tx10
Drilling machine with 8 mm drill
Mounting tools for 8 mm plugs and screws
Hammer
Mounting tools for electrical cables and
wire end ferrules
Multimeter
EV simulator with phase order display
Required when replacing the charging
cable:
Mounting tools for cable glands M16
(wrench size 20 mm) and M32 (wrench size
36 mm)
8 Installation and electrical connection
Observe the safety information provided in section 2.
In addition to these installation instructions follow and
comply with the local regulations relating to operation,
installation and environmental protection.
The Webasto Pure safety concept is based on a po-
wer supply system that is earthed at all times, which
must always be ensured by an authorised electrician
during installation.
8.1 Requirements installation space
The charging station must be protected with a line circuit
breaker and residual current circuit breaker. The charging
station is equipped with a RDC-MD that safely isolates
the charging station from the power supply at the charge
output in the event of smooth DC fault currents > 6 mA.
A type A RCD in accordance with IEC 61008 or IEC 61009
or a type F RCD in accordance with IEC 62423 must be
connected upstream to protect against AC fault currents
and pulsating direct currents. The tripping fault current
Amount
1
1
1
1
1
1
1
1
1
1
Webasto Pure
Advertenties
Inhoudsopgave
