Unit Description - Webasto Pure Bedienings- En Montagehandleiding
Verberg thumbnails
Zie ook voor Pure:
- Bedieningshandleiding (13 pagina's) ,
- Bedienings- en installatiehandleiding (10 pagina's) ,
- Bedienings- en montagehandleiding (11 pagina's)
Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
■
■
Ensure only persons who have read these ope-
rating instructions have access to the charging
station.
2.3 Safety information for installation
■
■
Installation and connection of the charging
station must only be carried out by an authorised
electrician.
■
■
Only use the supplied installation material.
■
■
The Webasto Pure safety concept is based on a
power supply system that is earthed at all times.
The authorised electrician must ensure this requi-
rement during installation.
■
■
Do not install the charging station in an explosion
sensitive area (EX zone).
■
■
Install the charging station in such a way that the
charging cable does not block any passageways.
■
■
Do not install the charging station in areas subject
to ammonia or air containing ammonia.
■
■
Do not install the charging station in a location
where falling objects (e.g. extension reel or tyres)
can damage the charger.
■
■
The charging station is designed for use indoors,
e.g. garages as well as for use in protected
outdoor areas, e.g. carports. Do not install the
charging station in the vicinity of water jets, e.g.
car wash installations, high pressure cleaners or
garden hoses.
■
■
The charging station shall not be exposed to
direct rain to prevent damage due to freezing,
hail or similar.
■
■
Protect the charging station from direct sunlight.
The charging current may be reduced at high
temperatures or charging may be disabled
completely.
■
■
The installation location of the charging station
should be selected such that vehicles cannot
inadvertently collide with it. Protective measures
must be implemented if the possibility of damage
cannot be ruled out.
■
■
Do not place the charging station into operation
if it is damaged during installation. A replacement
will be required.
4
2.4 Safety information for electrical connection
■
■
Comply with the locally applicable requirements
pertaining to electrical installations, fire protec-
tion, safety regulations and escape routes at the
intended installation location.
■
■
Each charging station must have its own residual
current circuit breaker. The residual current circuit
breaker should be at least Type A (30 mA AC
tripping current, see chapter 8.1).
■
■
Make sure that the electrical connections are de-
energised before connecting the charging station
to the power supply.
■
■
Do not connect a vehicle during initial start-up of
the charger.
■
■
Make sure that the correct supply cable is used
for the power connection.
■
■
Do not leave the charging station unattended
with the cover open.
■
■
Do not install the charging station without the
mounting frame.
■
■
Change DIP-switch settings only with the power
off.
■
■
Register with the power supply company as
required.
2.5 Safety information for initial start-up
■
■
Initial start-up of the charging station must be
carried out only by an authorised electrician.
■
■
Prior to initial start-up, the authorised electrician
must check that the charging station has been
connected correctly.
■
■
Before starting-up the charging station, check the
charging cable, charging coupling and the char-
ging station for visible damage. The charging stati-
on must not be started up if it is damaged or if the
charging cable/charging coupling is damaged.
3 Unit description
These operating and installation instructions describe the
Webasto Pure charging station. The exact unit description
is indicated on the type plate of the charging station (see
example Fig. 01).
4 Operation
4.1 Overview of the Webasto Pure
See Fig. 11
Legend:
1. LED indicator
2. Touch control switch
3. Charging cable holder
4. Charging coupling holder
5. Key-operated switch, accessible from below
6. Installation cover
Webasto Pure
Advertenties
Inhoudsopgave
