Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
3. The device should avoid the ignition caused by
electrostatic discharge during normal use,
maintenance, and cleaning. Do not wipe the
device in the explosive gas environment. If it is
necessary to replace or wipe the device, it should
be finished in the environment without explosive
gas.
4. Charging or replacing batteries of the device is
prohibited in hazardous areas.
5. The device shall be protected from exposure to
daylight or light from luminaires.
6. The device shall only be charged when in the
non-hazardous area using a charger specifically
supplied by the manufacturer for use with the
unit. The charging temperature range is 0 °C to
45 °C.
7. The battery of device is prohibited to be
replaced by end users.
8. The interface cover shall block off the type-C
USB port in hazardous location.
9. Resistance to impact was tested corresponding
to the low risk of mechanical danger. The device
must be protected against strong impacts.
Safety Instruction
These instructions are intended to ensure that
user can use the product correctly to avoid
danger or property loss.
Laws and Regulations
● Use of the product must be in strict compliance
with the local electrical safety regulations.
Transportation
● Keep the device in original or similar packaging
while transporting it.
● Keep all wrappers after unpacking them for
future use. In case of any failure occurred, you
need to return the device to the factory with the
original wrapper. Transportation without the
original wrapper may result in damage on the
device and the company shall not take any
responsibilities.
● Do not drop the product or subject it to physical
shock. Keep the device away from magnetic
interference.
Power Supply
● The input voltage should meet the Limited
Power Source (3.7 VDC, 0.5 A) according to the
IEC61010-1 standard. Please refer to technical
specifications for detailed information.
● Make sure the plug is properly connected to the
power socket.
● DO NOT connect multiple devices to one power
adapter, to avoid over-heating or fire hazards
caused by overload.
● Use the power adapter provided by a qualified
manufacturer. Refer to the product
specification for detailed power requirements.
Battery
● The built-in battery cannot be dismantled.
Please contact the manufacture for repair if
necessary. The battery may explode if it is
replaced by an incorrect type. Replace with the
same or equivalent type only. Dispose of used
batteries in conformance with the instructions
provided by the battery manufacturer.
● Use the battery provided by a qualified
manufacturer. Refer to the product
specification for detailed battery requirements.
● For long-term storage of the battery, make sure
it is fully charged every half year to ensure the
battery quality. Otherwise, damage may occur.
● Make sure the plug is properly connected to the
power socket.
● When the device is powered off and the RTC
battery is full, the time settings can be kept for
4 months.
● Before the first use, charge the lithium battery
for more than 8 hours.
Maintenance
● If the product does not work properly, please
contact your dealer or the nearest service
center. We shall not assume any responsibility
for problems caused by unauthorized repair or
maintenance.
● Wipe the device gently with a clean cloth and a
small quantity of ethanol, if necessary.
● If the equipment is used in a manner not
specified by the manufacturer, the protection
provided by the device may be impaired.
● Your camera will periodically perform a self-
calibration to optimize image quality and
measurement accuracy. In this process the
image will pause briefly and you will hear a
"click" as a shutter moves in front of the
detector. The self-calibration will be more
frequent during the startup or in very cold or
hot environments. This is a normal part of
operation to ensure optimum performance for
your camera.
Calibration Service
● We recommend you send the device back for
calibration once a year, and please contact the
local dealer for the information on
maintenance points. For more detailed
calibration services, please visit
https://www.hikmicrotech.com/en/support/cal
ibration-service.html.
4
Advertenties
Inhoudsopgave
