Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Problem
Sparse coffee dispensing, only
drop by drop
Weak "body"
The machine does not stop
working when there's no water in
tank and takes in air.
Foam instead of crema
Portafilter/ brew group is
dripping.
The display shows a dot.
The display shows "CLn".
If the machine will not be used for a long period of time, it is recommended to
.. clean the brew group (see instructions in chapter 7.2). Afterwards, do not clamp the portafilter back into
the group.
.. empty the boiler. Switch the machine off (power switch in position "0") and open the hot water dispenser.
Due to the boiler pressure, the boiler water is now discharged by the hot water dispenser. Close the hot water
lever valve again after emptying the boiler. To restart the machine, see chapter "First use".
How to froth milk
•
If possible, use cold and fresh milk with a fat content of approx. 1.5 % or 3 %. Even homogenized milk is
suitable - if you prefer.
•
Use a frothing container (made of metal) with a minimum volume of 0.5 litres. The size of the container
should not be too wide. A narrow and high container is better.
•
Open the steam valve for approx. 5 seconds to release the condensation water and to create dry steam.
•
Fill 1/3 of the frothing container with milk and place it under the steam nozzle. The nozzle should be
immersed in the middle of the frothing container, just below the surface.
•
Slowly open the steam lever valve. Steam pervades the milk.
•
Keep the frothing container still.
•
After a few seconds you will notice a light suction in the milk jug. Proper frothing begins. Move the milk
jug downwards as the milk level increases. The steam nozzle must be kept under the surface of the
frothed milk.
•
When the desired amount of milk froth is reached, immerse the entire steam nozzle in the frothing
container for a short time and close the steam lever valve
Milk proteins "froth" with a temperature up to 77°C.
Once this temperature is exceeded, the milk does not froth any further.
•
Advice: When milk frothing is finished, just shake the frothing container a little bit in order to make the
milk bubbles ascend to the surface and to get a compact milk froth.
•
After frothing the milk, release the steam into the drip tray to avoid blockage of the steam nozzle.
Translation of the original German user manual
Possible Cause
The grind is too fine.
There is too much ground coffee.
The grind is not fine enough.
The coffee is old.
The amount of ground coffee is
not enough.
The shower screen is dirty.
Machine in use with water tank,
but switch in position "1" (=
position direct water connection).
The beans are improper.
The setting of the coffee grinder
is not suited for the coffee beans
in use.
Machine in use with water tank,
but switch in position "1" (=
position direct water connection).
Portafilter is not fixed properly.
Group gasket is broken.
The display is switched off
The reminder for the brew group
cleaning is programmed..
Troubleshooting
Use a coarser grind.
Tamp ground coffee only slightly.
Increase the brewing-pressure.
Use approx. 7 g of coffee for
every cup.
Use a finer grind.
Use fresh coffee.
Use approx. 7 g of coffee for
each cup.
Clean the shower screen.
Switch to position "0" (=position
water tank).
Use another coffee bean.
Adjust the coffee grinder (When
changing the coffee beans,
changing the grind may also be
necessary.)
Switch to position "0" (=position
water tank).
Fix the portafilter properly.
Change group gasket and shower
screen.
Press + to turn on the PID.
Clean the brew group (Chapter
7.2)
ENGLISH
35
Advertenties
Inhoudsopgave
Probleemoplossen
