Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
4/ INSTALLING YOUR WINE CABINET
Precautions (Continued)
• For single-temperature models only:
- If you notice low humidity levels (<55%) a few days after setting
your wine cabinet into operation, we recommend that you use the
humidity cartridge, supplied in a bag with the appliance. Place it at
the bottom of the cabinet, under the rack in the drip tray provided
(see diagram below). When using for the first time, completely
immerse your cartridge in tap water for a few minutes to saturate
it then allow it to dry. Depending on external conditions, it may
be necessary to add a 10cl glass of water after several months.
- If the appliance is not able to reduce humidity levels to the desire
value, remove the black discharge pipe located at the base of the
cabinet.
•
•
• Install the stop (which is
located in the accessories bag)
at the back of the cabinet (see
diagram).
• This allows a space of 7 cm
to be maintained between
the wall and the rear of the
cabinet. This space allows your
cabinet's power consumption
to be optimised.
• Place the 2 caps in the 2 holes
at the top of the cabinet.
• Do not push the caps all the way in, in order to allow the rear stop to
be installed.
• Slide the rear stop between the caps and the wall of the cabinet, then
push the 2 caps all the way in.
24
GB
Installation
Place your cabinet in the desired location.
It must:
• be open to the outside and well ventilated (not in an enclosed cupboard,
for example),
• not be too damp. Max 85% ambient humidity (linen cupboard, laundry
room, bathroom...),
• have a flat, stable floor,
• be supplied with power (standard outlet, 16 A, earthed with 30 mA*
circuit breaker). (* not applicable to some countries).
• Place your cabinet in the desired location.
• Fit the charcoal filter (located in the "accessories" bag) by inserting it
into the breather hole located on the top left-hand side of the inside
of your cabinet.
•
Wait 48hrs before
plugging in your cabinet
•
When
using
cabinet for the first
time, the charcoal
filter alarm will display.
Reset the filter meter
to 365 (see chapter
6, § VII).
Installation of two cabinets side by side
Caution: In the case of two side by side cabinets installed in extreme
conditions (Temperature >30°C - Relative Humidity > 70%), in order to
prevent condensation of stagnant air between the walls, please leave either
a minimum space of 5 cm between the two cabinets, or fill the space with
a foam sheet to remove the void.
Replacement of the LEDs on the control panel
must only be carried out by a qualified electrician.
Bottles must be arranged so that they do not come into
contact with the back wall. If this happens, the condensation
created on the wall may trickle onto the shelves and damage
the bottle labels. In addition, contact with the cold wall may create a
frost point, which is harmful to your wine.
Your EuroCave Professional cabinet was designed to be adaptable. Its storage equipment adapts to your requirements and can be added to over
time.
We strongly recommend that you do not leave your wine bottles:
- Wrapped in tissue paper inside your EuroCave wine cabinet. Tissue paper does not tolerate ambient humidity in the long-term. The saturated
paper will stick to your bottle labels and damage them.
- Stored in cardboard packaging or a wooden case in your EuroCave wine cabinet, in order to encourage maximum air flow around the bottles
and prevent the packaging from deteriorating, which could eventually contaminate your wine bottles.
Loading and layout advice
Each shelf can be used as a storage shelf, sliding shelf or display shelf. The shelves in your cabinet have 12 recesses, allowing your
bottles to be stored safely.
1
2
3
30 dowel pins supplied in the accessories bag.
your
Diagram 1
Diagram 2
Diagram 3
5/ LAYOUT – STORAGE
1
Runners (x2)
2
Shelf - 12 recesses
3
Dowels (x2)
Installing a shelf in storage version
To install bottles on a storage shelf, proceed as follows:
1. Insert 2 runners in the shelf support strips. For each shelf, position one runner on
the right and one runner on the left (see diagram 1). Ensure that the runners are
correctly fixed in their housing (see diagram 2)
2. Place the shelf in the 2 runners. (see diagram 3)
3. Place a locking dowel in each of the 2 holes located at the front of the shelf, in the
upper section. These pins then fix the shelf with respect to the runner and prevent
any unwanted movement.
4. Start by placing bottles in each recess of the back row with the base of the bottle
towards the back.
5. Continue by placing the bottles in the opposite direction on the front row.
6. Continue stacking the bottles, ensuring that no bottles touch the back wall.
7. A storage shelf can support a maximum of 6 rows of 12 bottles, i.e.72 traditional
Bordeaux bottles (97 kg).
25
GB
Advertenties
Hoofdstukken
Inhoudsopgave
