Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
INSTALLATION MANUAL
!Caution
- Take the minimum internal width of the
chimney breast into account: 750 mm
(see fi g. 2);
- When placing the chimney breast, you
should take the location of the ventilation
holes (V) into account (see fi g. 2).
!Tip
You should preferably apply the ventila-
tion holes on both sides of the chimney
breast. You can use DRU ventilation
elements.
• Check whether the fl ue gas discharge system is placed
correctly.
• Check the fi xture of the clip binding with self-tapping
screws on places that cannot be reached later on.
• Do not apply plaster on or over the fl anges (see fi g. 2,
maximum plaster line M), because the heat of the appli-
ance could cause cracks.
• If necessary, place the decorative strip or front around
the appliance; also see the instructions included with the
delivery.
• When using stone-like materials and/or plaster fi nishing,
the chimney breast should dry for at least 6 weeks before
it is taken into operation, in order to prevent cracks.
6.7 Placing the wood set
The appliance is supplied with a wood set.
Caution
Strictly observe the following instructions
to prevent unsafe situations:
- only ever use the supplied wood set;
- place the wood set exactly as described;
- make sure the pilot burner and the space
around it are kept free from objects (see
fi g. 5a);
- make sure thermocouple 2 and the sur-
rounding space remain free (see fi g. 5a)
- make sure there is no vermiculite's fi ne
dust on the burner.
6.7.1
Wood set
The wood set consists of black vermiculite (see fi g. 6a),
chips (see fi g. 6b) and four logs.
• Fill the burner tray with vermiculite; equally spread the
vermiculite.
!Caution
- You can infl uence the fl ame image by
moving the vermiculite, yet
- the burner deck has to remain covered
with vermiculite in order to prevent that
the life expectancy of the burner is
reduced.
• Identify logs A up to D by using fi g. 7a.
!Tip
Use the burn stains on the logs for identi-
fi cation.
• Successively place log A (rear log), log B (middle log) and
log C (right log); see fi g. 7b to 7h.
!Caution
Use the placement brackets as indicated
in the fi gures.
• Fill the tray surrounding the burner with chips; equally
spread the chips; see fi g. 7j.
• Finally place log D, the left log; see fi g. 7k.
6.8
Glass pane
After placing the wood/pebble set you can place the glass
pane, as described below.
!Caution
- Avoid damages when removing/placing
the glass pane;
- Use the Allen key supplied for loosening/
tightening the Allen screws.
6.8.1
Removing the glass pane
Remove the glass pane in accordance with the following
instructions (zie fi g. 10a up to fi g. 10d)
• Loosen the Allen screws in the upper glass strip by one or
two strokes.
• Grab the upper glass strip at both sides.
• Pull the glass strip to the front and
• Push it upwards.
• Slightly tilt the top of the glass pane towards you.
• Grab the glass pane at both sides.
• Remove the glass pane from the lower glass strip.
6.8.2
Placing the glass pane
• Place the glass pane in the lower glass strip.
• Pull the upper glass strip to the front and
• Push it upwards.
• Tilt the top of the glass pane away from you.
• Place the upper glass strip over the glass pane.
• Push on the upper glass strip.
• Retighten the Allen screws
!Caution
- Avoid/remove fi ngerprints on the pane,
since otherwise they will burn into the
surface;
- The Allen screws must not be over-
tightened, since otherwise they could
strip the thread: tight=tight;
7. Wireless remote control
The appliance is supplied with a wireless remote control.
Ignition, controlling the fl ame height and switching off are
performed by a remote control that operates a receiver.
User Manual, chapter 4, Wireless Remote Control, des-
cribes the operation of the appliance including the way the
remote control works.
Caution
Do not ignite the appliance until it is fully
installed.
28
Advertenties
Hoofdstukken
Inhoudsopgave
