Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Securing/attaching the carrying harness
♦
Hook the carrying harness
♦
Adjust the carrying harness
is at hip height when the strap is hooked in place.
Fitting the hedge trimmer
♦
First, undo the locking screw
♦
Push the pin on the front boom
on the boom
on the engine unit as far as the stop.
You have to make sure that the spring-loaded ball engages in the hole
provided.
♦
Tighten the locking screw
NOTE
►
The assembly for the pole pruner/strimmer/3-tooth cutting blade/
extension attachment is done in the same order.
Removing the hedge trimmer
♦
Undo the locking screw
and pull the front boom
trimmer out of the boom
on the engine unit.
NOTE
►
Dismantling the pole pruner/strimmer/3-tooth cutting blade/exten-
sion attachment is done in the same order.
Swivelling the hedge trimmer
♦
Release the lock/release
.
♦
Press the control lever
and swivel the hedge trimmer into the
desired position.
WARNING!
►
The cutter bar
must not be pivoted completely backwards parallel
to the front boom
in order to work with it.
There is a risk of injury! This position only serves as a transport
position.
♦
Allow the control lever
to click into the recess in the base plate
(hedge trimmer)
.
Mounting the saw chain and blade
WARNING!
►
Wear protective gloves! There is a risk of injury from the sharp cutting
teeth.
NOTE
►
Pay close attention to the running direction of the saw chain
the blade
and at the base plate (hedge trimmer)
►
Depending on wear, the blade
♦
Undo the nut
using the spark plug wrench
♦
Remove the sprocket cover
♦
Place the saw chain
around the blade
♦
Now fit the blade
and saw chain
♦
Lay the guide rail
over the blade guide
tensioner pin
in the blade hole
chain
over the chain sprocket
♦
Now you can tighten the saw chain
checking the saw chain").
♦
Replace the sprocket cover
│
GB │ IE │ NI
■
10
into the carrying lug
.
to your size so that the carrying lug
on the boom
of the engine unit.
of the hedge trimmer into the opening
.
of the hedge
can be turned.
.
.
starting at the tip.
.
, while inserting the chain
. At the same time, lay the saw
.
(see section "Tightening and
and tighten the nut
firmly.
Removing the saw chain
♦
You may have to loosen the saw chain
and the saw chain
saw chain"). Follow these instructions in reverse order.
Tightening and checking the saw chain
WARNING!
►
Wear protective gloves! There is a risk of injury from the sharp cutting
teeth.
♦
Turn the chain tensioning screw
screwdriver
to increase the tension.
♦
The saw chain
whether the saw chain
NOTE
►
A new saw chain
Chain lubrication
♦
Remove the oil filler cap
♦
Fill the oil tank
♦
The chain lubrication can be increased or decreased using the oil
adjusting screw
♦
Press and then turn the oil adjusting screw
the chain lubrication.
♦
Press and then turn the oil adjusting screw
the chain lubrication.
WARNING!
►
Never work without chain lubrication!
If the saw chain runs dry, the cutting equipment may become irrepa-
rably damaged within a short time. Always check chain lubrication
and oil level in the tank before starting work.
NOTE
►
Use only saw chain oil, preferably biodegradable. Do not use waste
oil, motor oil, etc.
►
While working, check whether the chain lubrication is working
correctly.
Sharpening the saw chain
NOTE
►
A bench grinder can be attached to the grinder support
on
secure grip during grinding.
.
►
You will find detailed information on sharpening in a sharpening set,
e.g. from Oregon.
►
Alternatively, you can use an electrical saw chain sharpening device
and follow the instructions of the manufacturer.
►
If you have any doubts about carrying out the work, the saw chain
should be replaced.
to remove the blade
(see section "Tightening and checking the
clockwise using the flat-blade
must lie against the underside of the blade. Check
can be drawn by hand over the blade
stretches and must be tightened more regularly.
.
with approx. 100 ml of organic chain oil
.
clockwise to decrease
anticlockwise to increase
.
.
for a
PBK 4 A2
Advertenties
Hoofdstukken
Inhoudsopgave
Probleemoplossen
