Advertenties
Beschikbare talen
Beschikbare talen
GB
of the wires of the power cord of the appliance. This should be checked on the insulation of
the power cord and the extension cord, or contact the manufacturer of the appliance and/or
the extension cord. Do not use the appliance with damaged equipment parts If you notice
any damage to any part of the appliance or accessory, you must discontinue using it. In this
case, the appliance must be taken to an authorised service centre or replaced by yourself,
if this is permitted by the user's manual. Turn off the appliance and unplug the power cord
from the wall socket before you start any work on replacing, cleaning, or adjusting moving
parts. The appliance must not be used by children. This appliance may be used by persons
with reduced physical, mental abilities and persons with no experience or knowledge of the
appliance, if supervised or instructed on its safe use so that the risks associated with it were
understandable. Children should not play with the appliance. Unattended children should
not be allowed to perform the cleaning and maintenance of the appliance.The appliance
contains sharp parts (shredder inserts), and special care should be taken when assembling,
disassembling and cleaning such parts. The appliance is intended for home use only. It is
recommended not to exceed 6 minutes of continuous operation, after which the appliance
should be left to cool down for about 20 minutes . During cool-down, unplug the power cord
from the power socket.
APPLIANCE OPERATION
CAUTION! Turn off the appliance and unplug the power cord from the socket during accessory assembly and disassembly activities.
Preparing for operation
Remove the product from its packaging, remove all parts and then wash all parts in contact with the food according to the instruc-
tions in the section entitled "Product maintenance".
Shredder assembly and disassembly
Place the drive housing on a level and stable surface so that the ON/OFF switch is at the top. Make sure that all feet are in contact
with the ground.
Mount the shredder housing in the drive housing (II). The marker on the shredder housing should indicate the open padlock symbol
on the drive housing. Then rotate the shredder housing so that the marker shows the closed padlock symbol. An increased resistance
will be felt at the end of rotation, due to the latch which locks the shredder housing in the drive housing. A correctly mounted housing
has an upward-facing vertical inlet and cannot be removed other than by turning and pulling it out of the drive housing.
Mount the selected insert inside the shredder housing. The insert has an opening, the shape of which must be adjusted to the
shape of the drive axle (III).
Insert the pusher into the inlet of the shredder housing (IV) and check whether it slides in and out without problems.
The shredder is ready for use (V).
To disassemble the shredder, follow the above procedure in the reverse order. It is recommended to remove the shredder housing
only together with the insert, and only then dismantle the insert by pulling it out of the housing.
Citrus squeezer assembly and disassembly
Place the drive housing on a level and stable surface so that the ON/OFF switch is at the front. Make sure that all feet are in
contact with the ground.
Mount the squeezer container in the drive housing (VI). The marker on the squeezer container should indicate the open pad-
lock symbol on the drive housing. Then rotate the squeezer container so that the marker shows the closed padlock symbol. An
increased resistance will be felt at the end of rotation, due to the latch which locks the squeezer container in the drive housing.
A correctly mounted squeezer container has its spout facing front and cannot be removed other than by turning and pulling it out
of the drive housing.
Slide the squeezer into the container (VII). Ensure that the shape of the squeezer axis matches the shape of the drive axis.
The squeezer is ready for use (VIII). To disassemble the squeezer, follow the above procedure in the reverse order.
Ice cream maker assembly and disassembly
Place the drive housing on a level and stable surface so that the ON/OFF switch is at the top. Make sure that all feet are in contact
with the ground.
O R I G I N A L
I N S T R U C T I O N S
12
Advertenties
