Inhoudsopgave
Advertenties
If
you release the throttle trigger, the saw chain will
stop an
d the engine will idle. If the saw chain runs in spite
of non-pressed throttle trigger, you have to adjust the idle
speed. (
"M
aintenance")
Stop ping the engine
Release the throttle trigger.
Switch the ON/OFF switch (8) to the position
Starting with warm en gine
S
tart the chain saw as described under "Starting with cold
engine", but leave the choke lever in
M
a
i
n
t
e
n
a
n
c
e
M
a
i
n
t
e
n
a
n
c
e
Before each maintenance and cleaning work
− Stop the engine.
− wait for stop of chain saw
− Remove the spark plug connector.
− Wear protective gloves in order to avoid injur
to the hands.
− Do not carry out maintenance work close to
open flames. Risk
Mainte
nance and repair work other than those des
chapter is only allowed to be carried out by service staff.
Use only
original parts. Other parts can result in unexpected
damag an
es
d injuries.
For maintaining and cleaning, removed security devices m
unconditionally be mounted properly and proved again.
Maintenance
To guarantee a long and reliable usage of the chain saws carry
out the following maintenance works regularly.
and cleaning schedule.
C
heck the chain saw for obvious defects such as:
− loose or damag
ed saw chain
− loose fastenings
− wear, especially chain, guide bar and chain wheel
− worn or damaged components
−
leaks from the fuel/oi
l tank cap or fuel lines
− correctly assembled and faultless covers and p
devices.
Necessary repair works or maintenance works ha
carried out before the usage of the chain saw.
25
All manuals and user guides at all-guides.com
.
its operating position
a
n
d
c
l
e
a
n
i
n
g
s
c
h
e
d
u
l
a
n
d
c
l
e
a
n
i
n
g
s
c
h
e
d
u
l
of fire.
cribed in this
Maintenance
rotective
ve to be
Adjusting the chain lubrication
Stop the engine!
T
he chain lubrication is factory-set. Depending on the type of
wood and working techniques the amount of oil may vary and
has to be corrected.
Adjust
the chain lubrica
a
djus g screw (12) which is located below
tin
the product.
Anticlockwise turning
Clockwise turning
.
The chain lubrication is correctly adju
saw chain throws off small amounts
operation.
e
e
Saw chain and guide bar
Saw chain and guide bar are exposed to a great extent of
wearing. Replace the chain saw and the guide bar without any
delay if their proper function is no longer ensured.
y
t
he guide ba
r and the chain saw".
Sharpening of saw chain
You can only work safely and well with a sharp
and clean saw chain. Damaged or incorrectly
sharpened saw chains increase the risk of
kickbacks.
The saw chain has to be sharpened
ust
only
wood dust is thrown out instead of shavings
you have to press the chain saw through the wood during
cutting
Inexperienced users: Have the saw chain sharpened by a
specialist/service workshop.
If you sharpen the saw chain by yourself, note the va
and use the supplied round file. (Additional accessories are
available from specialist shops.)
Saw chain type
Round file
Dep
th gauge distance T
Schärfwinkel α
Breast angle β
Planing tooth length a
Firmly clamp the chain
block the saw chain
To advance the saw chai
Use the supplied round
angles (α=35°).
Do only apply 2-3 strokes with the file.
The sharpening angles must be identic l. a
sharpening angles result in an erratic chain run or ch n
breaking.
tion using the
large amount of oil (MAX)
small amount of oil (MIN)
sted when the
of oil during
if
Carlton N1C-BL-57E
Ø 4 mm (5/32")
0
,56 mm (.022")
35°
60°
min. 3 mm
saw's guide bar in a
. App
ly the chain brake
n rele
ase the chain brake.
file (37) to file all sharpening
"Installing
lues below
vice and
.
Unequal
ai
Advertenties
Hoofdstukken
Inhoudsopgave
