Inhoudsopgave
Advertenties
HOLEX HCT electronic torque wrench
de
3.3.
DISPLAY
1
2
3
en
bg
10
zh
da
Menu
9
1 Battery capacity 2 Bluetooth (if Bluetooth activated) 3 Fault symbol/message
fi
symbol (if there is a fault) 4 Direction of rotation display 5 Time 6 Current torque
7 Unit of measure 8 Peak value 9 Menu 10 "Not calibrated" lights up: Measure-
ment within the non-calibrated range
fr
4.
Transport
Transport in the original packaging at temperatures between -20°C and +70°C and at
a humidity below 90%, non-condensing. Prevent from falling.
5.
Initial commissioning
it
A
CAUTION
hr
Exploding rechargeable batteries
Risk of injury to hands and body.
▶ Use only the rechargeable battery supplied.
▶ In the event of damage, deformation or heat build-up, stop using the re-
lt
chargeable battery.
▶ Only charge rechargeable batteries with the corresponding charger.
1. Turn rotary catch anti-clockwise with slot-head screwdriver and remove it.
nl
2. Remove contact fuse.
3. Insert rotary catch and turn clockwise with slot-head screwdriver.
6.
Switches on
B
no
i
Torque wrench is tared automatically each time it is switched on.
1. Place the torque wrench on a flat surface and keep it still.
pl
2. Press the OK button and keep it depressed for around two seconds in order to
switch on the torque wrench.
▶ "Tare - Do not move" is displayed.
CAUTION! Incorrect taring. Do not apply any loads to or move the
pt
torque wrench during the taring process.
3. If the torque wrench switches to measurement mode, the taring process is com-
plete.
ro
▶ The measurement mode last used is displayed.
7.
Menu navigation
7.1.
MEASUREMENT MODES
sv
i
Switch from main screen to Measurement method.
7.1.1.
Torque
sk
MODE
sl
Torque
es
Menu
1. If a password is required, press the Left/Back key in the main menu.
cs
2. Select "Mode" and confirm with OK.
3. Select "Torque" and confirm with OK.
4. Select "Indicating" mode and confirm with OK to measure the torque without
configuring further settings.
hu
5. Select "Triggering" mode in order to configure further settings.
In "Triggering" mode, configure the following device settings and confirm with OK:
12
4
5
16:32
0.0
6
Nm
7
8
Peak
UNITS
Define the desired unit of measure for the torque.
TARGET VALUE
Define the value of the target torque.
MIN TOLERANCE
Define the lower tolerance limit for torque.
MAX TOLERANCE
Define the upper tolerance limit for torque.
DIRECTION OF ROTATION
Define the direction of tightening.
7.1.2.
Optional Functions
7.1.2.1.
Angle of rotation
Chargeable enabling of the angle of rotation function under
http://ho7.eu/holex-hct-angle
MODE
Angle
Menu
1. If a password is required, press the Left/Back key in the main menu.
2. Select "Mode" and confirm with OK.
3. Select "Angle" and confirm with OK.
Configure the following device settings and confirm with OK:
UNITS
Define the desired unit of measure for the torque.
SNUG TORQUE
Define the value of the snug torque.
TARGET ANGLE
Define the value of the target angle.
MIN TOLERANCE
Define the lower tolerance limit for angle of rotation.
MAX TOLERANCE
Define the upper tolerance limit for angle of rotation.
DIRECTION OF ROTATION
Define the direction of tightening.
7.2.
HISTORY
i
History can be accessed via Hoffmann Group - Connected Tools (HCT) App
8.
Connection
MENU
16:32
0.0
Mode
Connection
Nm
Settings
Menu
Peak
back
1/4
1. If a password is required, press the Left/Back key in the main menu.
2. Select "Connection" and confirm with OK.
3. Select Bluetooth "ON".
4. For connection to a computer: Select HID "ON" and configure the following set-
tings:
Reset Bluetooth
App
Traceability
HID
Value separator
Data set separator
Nr. Separator
Keyboard lang.
Unit
Sign
8.1.
CONNECTING TO A SMARTPHONE VIA QR CODE
1. Display the QR code on the torque wrench.
CONNECTION
Bluetooth
ON
Resetting Bluetooth
OFF
QR code
SHOW
Menu
1/12
All existing Bluetooth connections, in-
cluding the linked connections, must be
delimited.
Activate the Bluetooth connection to the
app.
Secure data transmission mode to the
app.
Activate the Bluetooth HID connection to
the PC or mobile device.
Set the delimiter for separating the val-
ues and units when transferring to a
computer. Delimiter dependent on pro-
gramme used.
Set the delimiter for separating the indi-
vidual data sets when transferring to a
computer. Delimiter dependent on pro-
gramme used.
Set the decimal delimiter symbol for
measurement values. The delimiter is de-
pendent on computer keyboard lan-
guage.
Set the computer keyboard language.
Set whether the unit is to be transferred.
Set whether the sense sign (+/-) for the
direction of rotation is to be transferred.
Advertenties
Hoofdstukken
Inhoudsopgave
