Inhoudsopgave
Advertenties
GB
upper surface of the grater is aligned with the upper surface of the holder. Due to the sharp edges of the grater, special care
must be taken when installing and removing the grater in the holder. It is recommended to use protective gloves during assembly.
Close the mixer bowl with the lid. Place the lid on the bowl so that it is fl ush with the mixer bowl along its entire circumference,
and the tab of the safety device is next to the handle of the mixer bowl (VII). Then rotate the lid in the direction indicated by the
closed padlock symbol (VIII).
The safety device will not allow the drive to start if the lid is removed or incorrectly mounted.
Insert the pusher into the lid inlet opening (IX). The pusher consists of two elements, an external and an internal one. The opening
in the external pusher can be used for placing small food products in the bowl.
Installation and removal of the blender cup
Place the drive housing on level and stable surface. Make sure that all suction cups in the base have attached themselves to the surface.
Place the cup on top of the drive housing so that the cup's bottom edge is fully fl ush with the drive housing wall along the entire
circumference and the marker at the bottom edge of the cup points to the open padlock symbol (X), and then rotate the cup so
that the marker points to the closed padlock symbol (XI). The correctly installed cup's lower edge is fl ush with the entire circumfer-
ence of the upper wall of the drive housing. A correctly mounted cup cannot be dismantled except by turning it, so that the marker
indicates the open padlock symbol, and lifting. The drive housing has a safety device which, in case of improper installation, will
not allow to start the appliance rotation.
Mount the lid on the cup so that it is fully fl ush with the edge of the cup along its entire circumference and the tabs inside the cup
hit the notches in the lid and then rotate the lid in the direction indicated by the closed padlock symbol (XII). The cup spout should
be covered by the lid tab in such a manner as to limit the possibility of spilling the contents of the cup.
The lid is equipped with a plug (XIII), which allows to add food ingredients while the blender is in operation. The plug can also be
used as a measure to dose the amount of ingredients.
Mill assembly and disassembly
Place the drive housing on level and stable surface. Make sure that all suction cups in the base have attached themselves to the surface.
Fill the container of the mill with food intended for grinding to half the height of the container. Screw the mill base onto the container
(XIV). The base thread is counterclockwise, so in order to connect the base with the container, hold the container and turn the base
counterclockwise. Removing the base and container will require rotation in the opposite direction.
Then rotate the assembled base and container 180
and place the mill base on top of the drive housing so that the base's bottom
O
edge is fully fl ush with the drive housing wall along the entire circumference and the marker at the bottom edge of the cup points
to the open padlock symbol (XV), and then rotate the base so that the marker points to the closed padlock symbol (XVI).
The safety device will not allow the mill to operate without the container or with the base of the mill incorrectly mounted on the base.
Using the appliance
CAUTION! Before using the appliance for the fi rst time, all parts which come into contact with food should be thoroughly washed
and dried. Please read the maintenance instructions beforehand.
The appliance has a control panel with buttons which allow to switch the appliance on and off , set two speeds and start the pulse mode.
The ON/OFF button is used to turn the appliance on and off . If the appliance is switched on, the red backlighting of the ON/OFF
button will indicate that the appliance is switched on.
The buttons marked "I" and "II" are used to select the speed mode of the appliance. The button marked "I" allows a lower speed to
be set and the button marked "II" allows a higher speed to be set. The selected speed mode is indicated by the blue backlighting
of the button pressed.
The button marked "PULSE" is used to start the pulse mode. Press and hold to activate the maximum speed. Releasing the button
stops the appliance.
When fi nished, always turn off the product power supply using the ON/OFF button, wait for the moving parts to stop completely,
and then unplug the power cord from the socket. Only then can you proceed with the removal of the accessories.
Recommendations and tips for working with the food processor
Connect the appliance to the power supply after it has been assembled and fi lled with food. When using the mixer, only add food
through the inlet opening. When using the grater, allow the full speed to be reached and only then add food through the inlet opening.
Do not exceed the maximum capacity of bowls, cups and containers. If the vessel has a capacity scale, do not fi ll it above the
maximum capacity mark. If the vessel is fi lled with liquid, the rotary movement will cause the liquid level to rise. If the vessel is
overfi lled it can result in spilling the contents.
The chopping blade is not used for fragmenting hard food products such as coff ee beans, nuts, ice cubes. Too hard food products
can cause the blade to deform.
Starting the drive at a lower speed will reduce the risk of spillage or scattering food while the food processor is running. If neces-
sary, the speed can be changed during operation by pressing the corresponding switch.
Do not excessively prolong the working time when chopping hard cheese or chocolate. If the working time is too long, the cheese
or chocolate will start to heat up and melt, which may cause the chopped food to clump.
O R I G I N A L
I N S T R U C T I O N S
14
Advertenties
Inhoudsopgave
