Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
the lid
upwards using the handle (detecta-
4
ble mark).
Turn the shaping disc holder
and remove it from the pressing tube
shaping disc
is installed on the device, this
16
must also be removed.
Unscrew both fixing screws
anticlockwise at the same time, until the front
panel
can be removed from the housing
6
without difficulty.
Pull the pressing tube
8
out of the mixing chamber
7
Push the auger
out of the pressing tube
7
Pull the mixing chamber
ing paddle
forward to remove from the
5
housing
. The mixing paddle
2
automatically from the socket.
Remove the drawer
10
for cleaning.
Assembly
Make sure that the device is switched off and
unplug the mains plug from the socket before
assembling.
If you had previously removed the drawer
re-insert this into the housing
used shaping disks
.
16
Push the mixing chamber
housing
(see fig. A). The two guide pins at
2
the upper outer edge of the mixing chamber
should not yet lock into the corresponding
1
sockets on the housing
Insert the mixing paddle
chamber
from above.
1
Insert the mixing paddle
the back of the housing
now push the mixing chamber
ing paddle
into the housing
5
time as far as they will go.
From the front, insert the pressing tube
the opening with the help of the corresponding
socket (see fig. D).
Insert the auger
into the pressing tube
7
(see fig. E) until it completely disappears.
anticlockwise
9
. If a
8
by turning them
15
2
including the auger
.
1
.
8
including the mix-
1
releases
5
from the housing
2
,
10
with the un-
2
loosely into the
1
.
2
into the mixing
5
into the guide in
5
(see Fig. B+C) and
2
and the mix-
1
at the same
2
into
8
8
Fit the front panel
6
lock it in place by turning the fixing screws
clockwise (see fig. F).
Choose the desired shaping disc
nib on the back of the shaping disc
inserted into the silver opening at the end of
the pressure roller.
Now fix the shaping disc
out tube on the front (if necessary, hold fast
with one hand).
Screw the shaping disk holder
clockwise direction (see fig. F).
Note: Do not screw the shaping disk
tight. If you do, it will be very difficult to unscrew
after you have finished making pasta (due to
contact pressure).
Attach the lid
by inserting the two teeth into
4
the sockets on the housing
down until you hear it click. Assembly is now
complete (see fig. G).
Selecting a shaping disk
The following 8 shaping disks
the delivery contents (see fig. H):
-
thin spaghetti
16a
-
macaroni - made up of 2 parts
16b
-
triangular
16c
-
thick spaghetti
16d
-
lasagne / ravioli - made up of 2 parts
16e
-
linguine
16f
-
fettuccine
16g
-
pappardelle
16h
Make sure that the shaping disk holder
well fastened so that it doesn't have a negative
effect on your pasta production.
When using the shapes „lasagne / ravioli" and
„macaroni", make sure that you have inserted
the shaping disks
16
first holding the shaping disk
insert with one hand and screwing tight the
shaping disk holder
The length of time it takes to press out pasta
depends on the shaping disk
the small opening, it can take up to 3 minutes
onto the housing
and
2
15
. The small
16
must be
16
to the pressing
16
tight in a
9
too
16
. Press the lid
2
are included in
16
is
9
correctly. We recommend
and the relevant
16
with the other.
9
used. Due to
16
GB/IE
4
25
Advertenties
Hoofdstukken
Inhoudsopgave
