Inhoudsopgave
Advertenties
Behaviour in an emergency situation
Initiate all required first aid measures suited for the injury
and seek qualified medical advice as quick as possible.
Protect the injured person against further injuries and
immobilise the injured person.
Description of device / spare parts
+
Pos.
Designation:
1
Tube shaft upper part
2
Tube shaft lower part
3
Cutting blade guard
4
Guard extension for dual trimming
thread
5
Guide handle upper part
6
Guide handle lower part
7
Carrying strap
8
Thread head
9
Set of cutting threads (10 pieces)
9A
Cutting thread
10
Cutting blade with transport guard
10A
Cutting blade
10B
Transport guard
11
Rubber sleeve
12
Cover
13
Protective cover
14
Spacer washer
15
Fixing nut
16
Installation wrench
17
Angle key
18
Screw (Torx) M5x35
19
Screw (Philips) M5x12
20
Screw (Torx) M4x15
21
Thread knife
25
Safety label 1
26
Safety label 2
27
Safety label 3
28
Charger ALG 40-1800
29
Battery AP 40-2000 (2000 mA)
30
Battery AP 40-4000 (4000 mA)
Assembly
Always start the machine when it is completely
assembled.
Mounting the guide handle
Push the rubber sleeve (11) over the tube shaft upper part
(1).
Plug the guide handle lower part (6) and the guide handle
upper part (5) onto the rubber sleeve.
Secure both parts with 4 screws M5 x 35 (18).
Mounting the cutting blade guard
Plug the guard (3) on the drive unit (A).
Secure it with 3 screws M5 x 12 (19).
Mounting the cutting blade
First plug the guard (13) on the drive shaft (B), then in
sequence the cutting blade (10), spacer disc (14) and cap
(12). Screw the mounting nut M10 (15) counterclockwise
on the drive shaft.
Now rotate the hole (X) of the guard (13) over the recess
in the drive unit (A).
Order
Lock the drive shaft (B) using the angle key (17).
number
Tighten the mounting nut (15) using the assembly wrench
(16).
385939
Mounting the guard extension for the thread head
Fasten the guard extension (4) to the guard (3) using 4
385938
screws M4 x 15 (20).
Mounting the thread head and cutting threads
385805
Screw the thread head (8) counterclockwise on the drive
385940
shaft (B).
385933
Now rotate the hole (X) of the guard (13) over the recess
in the drive unit (A).
385934
Lock the drive shaft using the angle key (17).
Now tighten the thread head.
Guide two cutting threads (9) through the holes in the
thread head.
385941
385942
Cutting diameter of the cutting threads
385861
The cutting diameter of the cutting threads can be
385834
changed by turning the thread blade (21) over.
Position "A": 330 mm
Position "B": 380 mm
Connecting the tube shafts
Insert the tube shaft upper part (1) into the tube shaft
lower part (2) as far as it will go.
385935
385936
385937
Slide the locking nut (C) over the plug connection and turn
365500
it tight
365501
Fastening and adjusting the carrying strap
365503
Hook the carrying strap (7) in the suspension eye (D).
Make sure that the snap hook (E) of the carrying strap is
assembled and hooked in as shown.
The lithium ion batteries AP 40-2000 (Article No. 365501)
or AP 40-4000 (Article No. 365503) as well as the charger
ALG 40-1800 (Article No. 365500) are not included in the
scope of delivery and must be purchased separately.
!
Use only an original battery.
!
Do not use any other charger to charge the batteries.
The charger is optimally matched to the batteries.
Note the marks (►◄).
Before starting up
21
Advertenties
Hoofdstukken
Inhoudsopgave
