Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
as shown in Figure 6.
3. Remove the two parts of the belt from the back
of the seat and fit them again through the slot
most suited to the height of the child (Fig. 7).
4. Insert the shoulder straps, if any, again.
FASTENING THE CHILD CAR SEAT INSIDE
THE VEHICLE
5. Position the handle of the child car seat ver-
tically by pressing the two side adjustment
buttons (Fig. 8).
6. Position the child car seat on the car seat
where you intend to install it (Fig. 9).
7. Pull the car's safety belt and fasten it in the
relevant buckle by passing the waist belt
through the two blue guides on the side of
the Child Car Seat (Fig. 10).
8. Hold the chest belt and pull it, tensioning the
waist belt (Fig. 11). At the end of the opera-
tion, check that the waist belt is always in the
relevant blue belt guides.
9. Always keeping the chest belt tensioned,
pass it through the blue guides on the back
of the backrest (Fig. 12). Pull the belt as tight-
ly as possible without leaving any slack and
making sure it is not twisted.
WARNING! After installing the child car seat,
always check that the vehicle safety belt is
tightened and that the buckle does not force
the belt to come out of the relevant slot. Also
check that the buckle of the car belt is not in
contact with the point of passage of the belt
on the child car seat. These situations may
compromise the effectiveness of the child car
seat in the event of an accident.
WARNING! Never fit the seat belt in any way
not mentioned in this instruction booklet, as it
would compromise the child's safety!
INSTALLING THE CHILD CAR SEAT WITH
STANDARD BASE
The standard Kaily base can be supplied or pur-
chased separately as an accessory.
The base consists of two pieces: main structure
and rebound bar (Fig. E).
Before installing in the car, fasten the rebound
bar to the main structure by inserting it in the
appropriate seats until you hear it "click" into
place (Fig. 13).
WARNING: once the rebound bar is fastened
to the base, it is no longer possible to remove it.
WARNING: the base must always be used with
the rebound bar attached
To install the child car seat with base on the
vehicle seat, proceed as follows:
11. Position the base on the chosen vehicle
seat. Position it as seen in Fig. 14, in order to
touch the vehicle seat's backrest.
12. Pull the vehicle safety belt and fasten it to
the relevant buckle, inserting the horizon-
tal (waist) part of the belt through the two
blue slots (Q) marked by the blue arrow and
pull it as tightly as possible (Fig. 15).
13. Attach the child car seat on the base (rear
facing) and push it down until you hear it
click into place (Fig. 16).
14. Check that the child car seat is correctly
fitted on the base by lifting the front and
rear sections. If it does not attach, press the
H release button (Fig. 18) and repeat the
process.
15. Pull the diagonal car safety belt and thread
it through the relevant slot (I) on the back
of the child car seat's backrest (Fig. 17).
WARNING! When travelling by car, this dia-
gonal safety belt must ALWAYS be threaded
through this slot.
16. Pull the belt as tightly as possible without
leaving any slack and making sure it is not
twisted
WARNING! After installing the child car seat,
ALWAYS check that the vehicle safety belt is
tightened properly along the entire length of
the belt and that no parts are twisted. NEVER fit
the car safety belt in any other way not mentio-
ned in these instructions.
To remove the child car seat leaving the base
on the vehicle seat:
17. Unthread the diagonal belt through the
guides in the backrest without removing it
from the buckle.
18. Remove the child car seat as illustrated in
Fig. 18.
POSITIONING THE CHILD
19. Press the aluminium button in the front part
of the Child Car Seat (covered by the fabric)
and loosen the two shoulder straps on the
Child Car Seat while holding it down (Fig. 19).
20
Advertenties
Inhoudsopgave
