Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
9. Removing the fitting
NOTE
Strength class ≥ 8.8
The L1 screws for the SmartHandle AX in its PAS24 version must have a
strength class of at least 8.8.
3.
Identify the cutting points on the L2 cut-to-size screws.
23
4.
Cut the L2 cut-to-size screws.
24
5.
For 7 mm spindle: place the adapter sleeve in the inner handle in such a
way that the recess faces the grub screw.
25
6.
Determine your inner handle's direction rotation as viewed from the in-
side: clockwise (clockwise = CW) or anti-clockwise (counter-clockwise
= CCW).
26
27
7.
Insert the interchangeable plate into the inner handle as required.
28
29
8.
Press the spring plate on one side against the interchangeable plate so
that the spring is compressed.
30
9.
At the same time, hook the spring plate tabs into the slot in the inner
handle.
31
10. Press down the spring plate bracket.
32
9
The inner handle is now ready.
33
11.
For 7 mm spindle: insert the adapter sleeve onto the side of the spindle
with the pin.
34
12.
Insert the spindle with the pin side into the fitting.
Pin will snap into position in the mount.
9
35
13.
For 8.5 mm and 10 mm spindle: slide the adapter sleeve into the centre
of the spindle. Use a punch and hammer to make an indent in the ad-
apter sleeve to prevent it from slipping.
36
37
14. Insert the fitting with the spindle into the door.
38
15.
Fasten the escutcheon base to the locking cylinder hole with the L2
screws (PH2, torque: 1.1 Nm).
39
16. Fasten the inner handle firmly with the L1 screws (PH2, torque 1.1 Nm).
40
17.
For FH: insert the dummy cylinder.
NOTE
Feed the blank cylinder into the hole using a screwdriver
It is difficult to position the blank cylinder correctly, especially in thick doors.
1.
Insert a screwdriver into the hole in the blank cylinder.
2.
Position the blank cylinder using the screwdriver.
30 / 52
41
42
18. For FH: screw the dummy cylinder firmly into place (PH2, torque 1.1 Nm).
43
19. Fasten the set screw on the inner handle firmly (TX15, torque 5.0 Nm).
44
20. Place the two cover plates with the notch facing downwards onto the
escutcheon base and the inner handle.
45
21.
Fit the outside handle into position on the fitting.
46
22. Firmly fasten the grub screw on the outside handle (TX15; torque: 5.0
Nm).
47
Fitting is now installed.
9
9. Removing the fitting
ü
1.5 mm hexagonal wrench available.
1.
Remove the fitting in the reverse order to installation.
2.
Insert a 1.5 mm hex key into the hole in the spindle mount in the fitting.
48
3.
Bend the hex key to the side where the hole is located while pulling on
the outside handle.
49
9
Fitting is now removed.
10. Replacing the batteries
NOTE
Malfunctions due to poor contact or different discharge
Contact surfaces that are too small/contaminated or different discharged
batteries can lead to malfunctions.
1.
Only use batteries that are approved by SimonsVoss.
2.
Do not touch the contacts of the new batteries with your hands.
3.
Use clean and grease-free gloves.
4.
Always replace all batteries at the same time.
ü
Special tool at hand.
Gloves at hand.
ü
1.
Insert the special tool into the fitting's cover inlay.
50
2.
Remove the cover with the tool.
51
52
3.
Carefully bend the battery clip inwards to detach it.
53
54
4.
Open the battery holder.
55
5.
Remove the battery holder.
56
6.
Remove the old batteries.
57
Digital SmartHandle AX PAS24
EN
Advertenties
Inhoudsopgave
