Advertenties
To secure the child, slide the hip belts into the shoulder straps (PIC.Z.I) and connect them by creating a central buckle (PIC.Z.II), and secure them with a
magnetic clamp until it locks (PIC.Z.III). To release the belts, press the buttons on the center buckle ( PIC.AA).
Safety belts can be fitted/removed. To remove the safety belts insert the shoulder straps and hip straps through the holes in the seat backrest and pull up
the crotch strap. Next, undo the zip on the back of the seat and insert the shoulder straps and hip straps through the holes (Fig.BB). Before you insert the
crotch strap through the hole, remove the seat liner, as shown in (Fig.CC). To fit the belts, repeat the steps in reverse order. The shoulder belts can be fitted
on one of the three heights and the crotch strap can be fitted on one of the two heights. Make sure that the buckles holding the belts are locked properly.
VI. SEAT POSITIONS
The seat can be set in 4 positions: 1 recumbent, 2 semi-recumbent, and 1 seated; the positions can be adjusted with the backrest adjustment lever (Fig.DD).
VII. ADJUSTING THE FOOTREST
You can set the footrest in one of the three positions. Press the buttons on both sides of the footrest simultaneously and set the footrest in the desired
position (Fig.EE). Additionally, you can push the footrest fabric liner up in order to lift the footrest (Fig.FF).
VIII. ADJUSTING THE HANDLE
To adjust the handle, push the button in the centre and set the handle in a comfortable position. You can adjust the height of the handle to one of the 4
levels (Fig.GG).
IX. ASSEMBLING THE CUP HOLDER, MOSQUITO NET AND THE TRANSPARENT RAIN COVER, MOMMY BAG
Fit the cup holder to the shank on the right hand side of the stroller.
Place the mosquito net over the seat (Fig.HH). The elastic band inside the edge will keep the net in the position.
Place the rain cover over the stroller and secure it using the button and eye under the stroller frame on its both sides (Fig.II).
Carry the bag (20) on the parent handle in the designated area ( Fig. PP). The bag contains a changing mat (21).
X. FOLDING THE STROLLER
When you use the stroller with the car seat or with the pram body, first remove these elements from the frame.
Detach the additional canopy (11) by using the zip (as shown in V.III). Fold the canopy. Fold the backrest flat towards the seat by pulling the adjustment
lever. Now press the button and pull up both levers of the frame (Fig.JJ) handle down whilst pulling the front wheels to the rear wheels until the 'click' is
heard. When the stroller is folded, the locking mechanism will activate automatically (Fig.KK). You can remove the wheels to reduce the size of the folded
stroller. The stroller can be folded with the seat attached to it in the forward facing position or in the rearward facing position. When folded, the stroller is
in the upright position, therefore the front wheels need to be locked so that the stroller cannot move forward; the handle has to be kept in its lowest
position.
XI. REMOVING THE SEAT COVER
The seat cover can be removed and washed. Detach the canopy first by following the instructions in V.III. Remove the armbar, unfasten the velcro strips
under the seat and then unzip the zip on the rear side of the backrest. Now detach the safety belts (as shown in V.V), pull the seat cover out of the frame
and remove the insert.
XII. ASSEMBLING THE CAR SEAT ON THE STROLLER FRAME
Click the right (R) and left (L) adapters (19) into both sides of the frame (Fig.LL). To attach the car seat to the adapters, click the car seat into the buckles,
one for each side of the stroller until you hear a distinctive clock (Fig.MM). To remove the adapters, press the buttons on both sides and pull up (Fig.NN).
NOTE! The car seat must always be fitted in such a way that the child should face
the carer.
XIII. CARE AND MAINTENANCE The buyer is responsible for proper installation of all functional elements as well as for carrying out all required maintenance
and adjustments in order to keep the buggy in good technical condition.
The buggy must be periodically checked for potential problems. Significant measures to be applied to ensure the child's safety and prevent shortening of
the product life have been presented below:
• Check the strength and safety of all rivets and connections.
• Check all wheel locking equipment and tyres. If necessary, replace or repair.
• Check if all safety devices work properly, particularly the main and additional fasteners that should move freely at any time.
Please, stop using the buggy if there are doubts as to its proper use or a suspicion of any danger.
If the wheels squeak, apply a thin layer of silicone. Do not use oil or grease based products as they attract dirt, which makes buggy movement difficult.
XIV. CLEANING
If the elements of the buggy chassis have been exposed to saltwater, rinse with tap water as soon as possible.
Do not wash. Clean the product gently with a damp
cloth and a mild detergent
Wash at max. 30°C, gentle process
Do not bleach
Do not iron
Do not fold or store the product when it is wet and never store it in wet conditions, as it can lead to mould growth.
Leg cover, Mosquito net, Pram body liner, Leg cover for pram body: maximum wash temp. 30°C; do not: bleach, tumble dry, iron, dry-clean.
Seat canopy, Basket, Canopy for the pram body, Transparent rain cover,mommy bag: do not wash. The product can be cleaned gently with a moist cloth
and mild detergent; do not: bleach, tumble dry, iron or dry-clean.
Seat cover, Mattress cover: hand wash; do not: bleach, tumble dry, iron, dry-clean.
XV. Warranty
The full text of the Terms and Conditions of the Warranty is available on the website WWW.KINDERKRAFT.COM
Hand wash
Do not dry in a tumble dryer
Do not dry clean
25
Advertenties
