Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
USER MANUAL
controlled in order to reach the set temperature.
To be able to use the day/night temperature function, the
appliance must be in the standby position.
!Caution
- Always leave the remote control at the
same place, so that the thermostat is able
to 'feel' the room temperature;
- Make sure this place is free from influen-
ces such as draught, heat from radiators
and direct sunlight.
Example
By using the Y TEMP function you can keep the day tempe-
rature at 20 ºC; while you use the TEMP function at night
to maintain a temperature of 15 ºC.
4.2.4.1 Setting day/night temperature
By using the SET button, you will go through the following
functions:
MAN Y TEMP TEMP (P*) TIMER MAN
• Briefly press the SET button to enter the Y TEMP or the
TEMP position.
• Press the SET button until the temperature on the display
flashes.
• Set the required temperature by using the buttons
(large flame) and
(small flame).
!Caution
- The minimum temperature you can set is
5 ºC / 40 ºF;
- Control of the night temperature is
switched off by lowering the temperature
until two stripes ("--") appear on the
display.
• Press the OFF button or wait until position Y TEMP or
TEMP appears on the display.
4.2.4.2 Activating the thermostat function
For activating the thermostat function, you must proceed
with the following steps:
• Place the appliance in the standby (pilot burner) position
using button
(small flame).
• Set the day/night temperature.
• Choose the Y TEMP or TEMP function using the SET
button.
4.2.5
Timer for thermostat function
Using the timer enables you to set two times per 24 hours
for switching on the day temperature and two times per
24 hours for switching on the night temperature.
In order to control the night temperature, it should be set
to at least 5 ºC / 40 ºF.
If the night temperature is set to the "- - " position, the
appliance will remain in the standby position. The appliance
will only switch on at the next switch-on time of the day
temperature.
The appliance must be in standby position in order to be
controlled by the timer.
Example of switch times
You have set a day temperature and night temperature of,
for example, 20 ºC and 15 ºC.
P1 Y TIMER = 7 hours; the temperature will go to 20 ºC
at 7 am.
P1 TIMER = 9 hours; the temperature will go to 15 ºC
at 9 am.
P2 Y TIMER = 17 hours; the temperature will go to 20 ºC
at 5 pm.
P2 TIMER = 22 hours; the temperature returns to 15 ºC
at 10 pm.
4.2.5.1 Setting times for the timer
To set the timer, proceed as follows:
• Set the day and night temperature as described above at
section 4.2.4.1.
• Briefly press the SET button to enter the (P*) TIMER
position.
• Press the SET button until P1 Y TIMER is displayed and
the time flashes.
• Set the first switch on time of the day temperature using
the buttons
(large flame) and
• Briefly press the SET button to set the next time of the
cycle, P1 TIMER.
• Successively set the times P2 Y TIMER and P2 TIMER.
• Press the OFF button or wait until position (P*) TIMER
appears on the display.
4.2.5.2 Activating the timer function
Follow the steps below for activating the timer control:
• Place the appliance in the standby (pilot burner) position
using button
(small flame).
• Set the day/night temperature if you have not yet done so;
for this, see section 4.2.4.1.
• Set the timer times P1 Y TIMER, P1 TIMER,
P2 Y TIMER and P2 TIMER.
• Choose the (P*) TIMER function using the SET button.
4.2.6
Replacing remote control battery
If the battery is almost empty, the display will show "BATT".
To replace the battery, proceed as follows:
• Remove the cover at the back side of the remote control.
• Disconnect the 9V block battery from / connect the 9V
block battery to the connector.
!Caution
- Observe the "+" and "-" poles of the
batteries and the connector;
- Use alkaline batteries;
- Batteries are regarded as "small chemical
waste" and may therefore not be
disposed with the household rubbish.
• Place the battery in the holder.
• Replace the cover.
42
(small flame).
Advertenties
Hoofdstukken
Inhoudsopgave
