Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
!Caution
- You can influence the flame image by
moving the vermiculite, yet
- the burner deck has to remain covered
with vermiculite in order to prevent that
the life expectancy of the burner is
reduced.
• Identify logs A up to C by using fig. 7a.
!Tip
Use the burn stains on the logs for identi-
fication.
• Place logs A, B and C; according to figures 7b to 7d
• Spread the glow wool over the burner; fix it under the
logs
6.8
Glass pane
After placing the wood set you can place the glass pane, as
described below.
!Caution
- Avoid damages when removing/placing
the glass pane;
- Use the Allen key supplied for loosening/
tightening the Allen screws.
6.8.1
Removing the glass pane
Remove the glass pane in accordance with the following
instructions (zie fig. 10a up to fig. 10d)
• Remove the front panel for the freestanding appliance
(Global beau) by lifting it out of the hooks and removing it
towards the front.
• Loosen the Allen screws in the upper glass strip by one or
two strokes.
• Grab the upper glass strip at both sides.
• Pull the glass strip to the front and
• Push it upwards.
• Slightly tilt the top of the glass pane towards you.
• Grab the glass pane at both sides.
• Remove the glass pane from the lower glass strip.
6.8.2
Placing the glass pane
• Place the glass pane in the lower glass strip.
• Pull the upper glass strip to the front and
• Push it upwards.
• Tilt the top of the glass pane away from you.
• Place the upper glass strip over the glass pane.
• Push on the upper glass strip.
• Retighten the Allen screws
• Place the front panel back in the hooks
!Caution
- Avoid/remove fingerprints on the pane,
since otherwise they will burn into the
surface;
- The Allen screws must not be over-
tightened, since otherwise they could
strip the thread: tight=tight;
7. Wireless remote control
The appliance is supplied with a wireless remote control.
Ignition, controlling the flame height and switching off are
performed by a remote control that operates a receiver.
User Manual, chapter 4, Wireless Remote Control, des-
cribes the operation of the appliance including the way the
remote control works.
Caution
Do not ignite the appliance until it is fully
installed.
7.1 Connecting the receiver
The receiver should be connected to the appliance, before the
batteries are installed.
The receiver will be placed under the burner.
Follow the procedure below (see fig. 11a):
• Fit the connection cable's brown plug to the receiver (see
fig. 11a, arrow F).
• Connect the white plug to the gas control.
!Tip
The plugs have different sizes that cor-
respond with the connectors.
• Connect the cables of the thermocouple to the receiver;
(see fig. 11a, arrows B).
!Tip
- The size of the eye corresponds with the
size of the screw;
- The colours of eye and screw also cor-
respond.
• Connect the ignition cable to the receiver;
(see fig. 11a, arrow A).
!Caution
The battery holder is in a tray at the bot-
tom of the gap between the combustion
chamber and the convection box of the
Global 40 CF. The battery holder of the
Global beau can be reached by removing
the front panel. Lift the front panel up from
the hooks and remove the front panel
towards the front.
• Connect the cable of the battery holder to the receiver
(see fig.11a, Arrow C and fig. 11b).
!Caution
Place the receiver in the holder
(see fig. 4a, arrow 1)
• Bend the antenna out of the clips; see fig. 11a, arrow D.
• Set the antenna straight.
!Caution
- Do not place the antenna too close to
the ignition cable and/or metal parts;
- Do not place the ignition cable over and/
or along metal parts: this will weaken the
spark;
- Do not lay the ignition cable over the
receiver: this could damage the receiver;
- Avoid dust on or in the receiver: cover it
when performing work.
29
INSTALLATION MANUAL
Global 40 CF
Advertenties
Hoofdstukken
Inhoudsopgave
