Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Place the appliance as follows:
• Apply the plaster strip if the appliance is built in tightly;see
the supplied instructions. (Global 40 CF)
• Determine the location of the appliance; see fig. 1 for the
dimensions of the appliance.
• Determine the construction height of the appliance.
(Global 40 CF).
• Provide a gas connection at the location. For details, see
section 6.3.
• Make a passage for the flue gas discharge system with the
following diameters. For details, see section 6.5.
- Ø90 mm for a roof terminal through non combustible
material;
- Ø 180 mm for a roof terminal through combustible material.
• Level the appliance on its destined location.
• Connect the gas pipe to the appliance, as described below.
The gas control is located below the burner. In order to
connect the gas pipe, you must remove the burner mounting
plate.
Follow the procedure described below:
• Remove the glass pane (see section 6.8).
• Store the glass pane on a safe place.
• Remove the two self-tapping screws from the cover under
the combustion chamber (see fig. 4a)
• Remove the cover under the combustion chamber (see fig. 4a)
• Remove the vermiculite tray (see fig. 4b)
• Unscrew the 4 self-tapping screws of the burner plate and
remove the burner plate plus accessories (see fig. 4c)
• Unscrew the Allen screws (4x) at both sides of the com-
bustion chamber using the supplied Allen key (see fig. 4d)
• Grab the combustion chamber at both sides and remove it
(see fig. 4e)
• Make a gas provision that runs into the convection box /
mantle (see fig. 4f)
• Connect the convection box of the built-in appliance to the
wall using the supplied key bolts and body rings (see fig. 4g)
• If necessary, blow clean the gas pipe.
• Place the combustion chamber back in the convection box
and fasten it at both sides with the Allen screws.
• Connect the flexible gas pipe to the gas connection with
gas tap.
Caution
- Avoid kinks in the pipe;
!Caution
Properly connect the flue spigot to the
draft interrupter when placing back the
combustion chamber (see fig. 4h)
• Bleed the gas pipe.
• Place the receiver; for details, see section 7.1 of the
Installation manual.
• Set the communication code between the remote control
and the receiver; see section 7.2 of the installation manual.
Caution
Do not ignite the appliance until it is fully
installed.
• Check the connections for gastightness as described in
section 8.1 of the installation manual.
• Check the line-pressure as described in section 8.2 of the
installation manual.
• Place back the burner mounting plate plus accessories and
fix it with the self-tapping screws.
• Place the vermiculite tray back in the combustion chamber.
!Caution
Position the vermiculite tray on the right
location by means of the stop edges (as far
as possible to the front)
• If applicable, remove the tape from the convection box
• Place back the cover under the combustion chamber.
• In case of the Global 40 CF, fix the cover with the self-
tapping screws
• Place the wood set; see section 6.7
• Place the glass pane; see section 6.8
6.5
Flue gas discharge system
For a connection to an existing chimney (different
from the class 1 chimney in the UK), a flexible SS pipe is
recommended for the discharge of flue gases.
!Caution
When constructed in a mantelpiece/fire-
place connected to an existing chimney
in Great Britain (class 1 chimney), the
separately supplied English description
'Fitting into a conventional class 1 chimney'
also applies. In addition to the installation
instructions, this booklet also contains sup-
plementary tests.
In case of the Global Beau CF, a ø130mm decorative pipe
is supplied which will fall over the first 500 mm of the
discharge system.
!Caution
This pipe only has a decorative function
and is therefore not part of the flue gas
discharge system.
6.5.1 General
The appliance is of the B
The passage to the outside is made with a roof terminal
(see section 6.5.2).
Caution
Use a suitable Ø80 mm diameter flue gas
discharge system provided with the CE
mark.
The flue gas discharge system is constructed from (the flue
spigot of) the appliance.
6.5.2
Connecting the flue gas discharge system
A Ø80 discharge pipe of at least 2 metres should be con-
nected to the appliance. It is not allowed to apply horizon-
tal pieces in the flue gas discharge system.
27
INSTALLATION MANUAL
type.
11AS
Global 40 CF
Advertenties
Hoofdstukken
Inhoudsopgave
