Bestway LAY-Z-SPA Handleiding pagina 11
Verberg thumbnails
Zie ook voor LAY-Z-SPA:
- Handleiding (28 pagina's) ,
- Handleiding (16 pagina's) ,
- Handleiding (340 pagina's)
Advertenties
SETUP INSTRUCTIONS
Suggested surfaces: grass, ground, concrete and all other surfaces that respect the above set-up conditions.
Surfaces to avoid: mud, sand, gravel, deck, balcony, driveway, platform, soft/loose soil or other surface that does not meet the above
set-up conditions.
Follow the important instructions above to choose the correct surface and location to set up your bath. If parts become damaged
because the set-up surface and location does not adhere to these instructions, it will not be considered a manufacturer defect and will
void the warranty and any service claims.
Additional Guidelines:
Check with your local city council for bylaws relating to fencing, barriers, lighting and safety requirements, and ensure you comply with
all laws.
If you must change locations during set-up, lift the liner to move it; do not drag it on the ground. The friction between the bottom and
the ground can damage the liner.
Parts & Tools Needed
Compare the parts in your box to the parts listed in this manual.
Verify that the equipment components represent the model that you had intended to purchase. If any parts are damaged or missing at
the time of purchase, visit our website bestwaycorp.com/support.
Assembly Instructions
For installation instructions, scan the QR code printed on the front cover or follow the illustrations inside the manual.
are for illustration purposes only. May not reflect actual product. Not to scale.
Assembly of the bath can be completed without additional tools.
Bestway is not responsible for damage caused to the pool due to mishandling or failure to follow these instructions.
IMPORTANT: The drawstring at the bottom of the bath should be installed in place, otherwise it will damage the product.
IMPORTANT: It is imperative to check that the hydraulic connectors are not obstructed.
IMPORTANT: Do not dry run the filter pump. Make sure both the bath's inlet and outlet are open and fully covered by water. Before
switching on the filter pump, perform the air discharging operation as shown.
AIR DISCHARGING OPERATION: Follow these steps to discharge air before switching the filter pump on and after every
maintenance operation. Omitting this operation will greatly affect the lifespan of the product.
Helpful Installation Tips:
The bath can be used when the environment temperature is above -20ºC / -4ºF. We strongly suggest opening the package and
assembling the bath when the ambient temperature is above 15ºC / 59ºF. The PVC material of the liner will be more flexible and
easier to assemble in this environment.
Filling the bath:
Consult your local government authority for water regulations related to convenient water supply for filling the bath.
Your bath can be filled with ice and cold water together, just ice or hot water up to 40°C / 104ºF.
ATTENTION: Do not use blocky ice with sharp edges that can damage the liner. Do not leave the bath unattended while filling with
water. It is highly recommended to use tap water for filling to minimize unwanted content, such as minerals. Do not use sea water. Fill
the bath with water after all assembly steps are completed and until the water reaches the proper water level. We strongly
recommend filling to the proper water level to avoid the overflow of water.
MAINTENANCE INSTRUCTIONS
Keeping your bath water clean and chemically balanced is necessary. Simply using the filtration system and cleaning the filter
cartridge is not enough for proper maintenance of the water.
It is important to prioritize the maintenance and health of your bath water. If you do not adhere to these guidelines, your and your
family's health might be at risk.
Water Maintenance:
We recommend you use chemicals to maintain water chemistry and chlorine or bromine tablets (do not use granules) with a chemical
dispenser.
The chemical maintenance with chemical tablets must be performed with a chemical dispenser or chemical floater. Do not throw
chemical products directly into the water. The chemicals will settle on the bottom of the bath and damage and discolor the liner. In the
worst cases, it will damage the structure of the bath liner.
Bath damage resulting from the misuse, number of users and overall mismanagement of bath water is not covered by the warranty.
Water quality is directly related to frequency of use, number of users and overall maintenance of the bath. The water should be
changed every 3 days if there is no chemical treatment being performed with the water. We recommend that you take a shower before
using your bath, as cosmetic products, lotions and other residues on the skin can quickly degrade water quality. Place a bucket of
water next to the bath to clean users' feet before they enter the water.
Use a skimmer for the surface and a vacuum cleaner for the bath bottom regularly to avoid settled dirt. If they are not included in the
set, you can purchase them by visiting our website (www.bestwaycorp.com) or by visiting the nearest supply store.
Chemical Usage:
Your bath set may not include a chemical dispenser. In this case, you can purchase one by visiting our website
(www.bestwaycorp.com) or by visiting the nearest supply store. Remove the chemical dispenser when the bath is in use. After
performing chemical maintenance and before using the bath, use a test kit (not included) to test the water chemistry. We recommend
maintaining your water's chemical balance as shown in the table below.
Exceeding the following parameters can damage the structure of the liner and create a dangerous situation for the users.
11
Drawings
Advertenties
