Inhoudsopgave
Advertenties
GB
Make sure that no liquid splashes onto the power tool housing. Liquid that has entered the power tool can cause damage
and lead to electric shock.
Follow the instructions and warnings related to the mixed material. Mixed material can be harmful.
If the power tool gets caught in mixed material, immediately disconnect the power tool from the mains and have it
checked by a qualifi ed service technician. Reaching the bucket while the tool is still attached can lead to electric shock.
Do not reach into the mixing container with your hands or put any other objects into it while mixing. Contact with the mixer
basket can lead to serious injury.
Start and lower the tool only into the mixing container. The mixer basket can bend or rotate in an uncontrolled way.
TOOL HANDLING
Before starting the work make sure that the housing and connecting cable with a plug are not damaged. Should any damage was
found, it is forbidden to continue the work.
Preparation to work
Warning! All actions associated with fi xing and replacing of accessories, and adjustment of rotational speed etc. should be car-
ried out with the power supply off , so prior to these actions: Pull out the plug of power cable from the mains socket!
Assembly of agitator (II)
Tighten the agitator's tip using spanners for mixer's spindle. The connector to be tighten fi rmly to prevent its spontaneous discon-
nection during operation.
Adjustment of rotational speed (III)
The spindle speed must be set using the regulator. The regulator knob has numbers on it, the larger the number visible on the
knob, the higher the spindle speed. Speed regulation is smooth.
Starting and stopping the mixer
Note! Prior to each start of operation, make a trial start for approx. 30 seconds. Trial start should be done without agitator sub-
mersed in the mass to be mixed. During trial start, please observe the operation of the agitator and the mixer. Proper work may
be started provided no symptoms of improper operation such as e.g. excessive oscillations, excessive noise or queer odour were
found during the trial start-up.
Use agitators appropriate for the specifi c job. Make sure that the swindle is not bent.
Take on working clothes as well as eye and ear protectors, and other personal safety equipment required when working with
particular material.
Make sure, that the switch of the tool remains in "off " position, insert the plug of mixer's power cable to mains socket.
Grab both mixer's grip handles with your hands.
Adopt a fi rm and stable posture.
Immerse the agitator in product to be mixed. Agitator's head should stay completely under the surface of the liquid being mixed.
This will prevent sloshing of liquid being mixed.
Turn on the mixer by pressing on the electric switch with a fi nger.
Mixer's switching off takes place after release of pressure on switch button.
In the event of long lasting operation you may use the switch lock. To enable the lock press the switch button and switch lock at
the same time. To release the lock press the switch button.
During the work avoid hitting the agitator against walls and bottom of container in which mixing is being carried out. Do not lean
the agitator against bottom of container. Do not keep the agitator in one position, displace it within the container, this will ensure
more homogenous and faster mixing.
Note! If any suspicious noise, crackles, odour, etc. were observed, immediately switch off the mixer and pull the plug out of the
mains.
Operating instructions
Do not use the product otherwise than as a mixer for mortars, paints and other liquid building materials. Do not mount any acces-
sories other than agitators, e.g. sanding discs, polishing discs, drills, etc. on the mixer. Do not use the mixer to mix loose products.
All accessories fi tted to the mixer must have a maximum speed greater than the rated product speed. It is forbidden to use acces-
sories with a maximum permissible speed lower than the rated speed of the product.
Damaged agitators must not be used. If cracks are noticed or the agitator shaft is bent, replace it with a defect-free agitator. Check
the condition of the accessories and product before each start-up.
Use agitators designed to work with a given type of material to be mixed. The agitator spindle rotates clockwise and the agitator
must be selected so that it aerates or deaerates the mixed mass. In the case of aeration, the agitator basket is designed in such
a way that during mixing a vortex will form on the surface of the mass to suck in the air. In the case of deaeration, the agitator is
O R I G I N A L
I N S T R U C T I O N S
12
Advertenties
Inhoudsopgave
