Inhoudsopgave
Advertenties
• Battery indicator: it shows the rest battery percent; please, charge when the battery is low.
• The breast pump will automatically stop working after 30 minutes of work.
INSTRUCTION FOR USE:
Cleaning and sanitizing (Figure III):
The main device, the USB cable and the adaptor do not require cleaning and sanitizing, as they do not come into contact with breast milk. Clean and sanitize all other parts
of the breast pump before first use.
• Do not heat or sterilize in a microwave oven.
• Before and after use, please clean and disinfect the parts in contact with breast milk.
Caution! Never put the main device, USB cable or the adaptor in water, in a dishwasher or in a sanitizer, as this causes permanent damage to these parts.
• Disassemble the breast pump completely as shown in Figure III.
• Before first use, disinfect in boiling water for 5 minutes all parts except the main device, USB cable and the adaptor. This ensures hygiene.
• Be careful when removing and cleaning the valve. If it breaks, your breast pump will not work properly.
• To clean the valve, gently rub it between your fingers in warm water with a little liquid detergent. Do not insert objects into the valve as this may damage it.
• Before first use, disinfect in boiling water for 5 minutes all parts except the main device, USB cable and the adaptor. This ensures hygiene.
• During the disinfection with boiling water, do not allow the parts to touch the side of the pot. This may cause irreparable deformation or damage to the product for
which KikkaBoo is not responsible.
• Clean carefully before each subsequent use to ensure hygiene.
• Wash all parts, except the main device, USB cable and the adaptor with warm water and delicate detergent.
• Always rinse all parts except the main device, USB cable and the adaptor thoroughly after each wash.
• Wash thoroughly and rinse all parts, except the main device, USB cable and the adaptor with clean water, including areas that may not be visible but through which the
milk has passed, to remove milk debris.
• All parts, except the main device, USB cable and the adaptor can be sterilized up to 10 minutes in a steam sterilizer intended for nursing mothers and baby products.
• Do not place in a dishwasher.
• Do not place in a microwave oven. Do not heat the product in traditional ovens, on hot plates or open flames.
• Avoid the use of sharp or abrasive materials, as this may damage the product.
• Do not clean or allow the product to come into contact with solvents or aggressive chemicals. This may damage the product.
• After cleaning the product, dry all parts thoroughly and store in a clean and dry place without direct sunlight and away from heat sources.
Note: Be sure to clean and disinfect the relevant parts of the breast pump. Wash your hands thoroughly before working on clean parts!
Warning! Be careful, as the cleaned parts may still be hot. Only start assembling the breast pump when the cleaned parts are cooled down.
Note: It is normal if there is a residual smell. Clean the product according to the instructions, it can help effectively reduce or eliminate the smell.
When to wash and sanitize (Figure I):
• Before first use wash and sanitize: the breast shield and the insert (I-11; I-12); breast pump kit (I-2; I-3; I-5; I-7; I-8).
• Before and after each use wash: the breast shield and the insert (I-11; I-12); breast pump kit (I-2; I-3; I-5; I-6; I-7; I-8)
• Once per day sanitize: the breast shield and the insert (I-11; I-12); breast pump kit (I-2; I-3; I-5; I-6; I-7; I-8).
Dry all parts after washing or sanitizing. Wash your hands and assemble the complete breast pump according to the figure IV.
BATTERY OPERATION:
WARNING! Before first use, fully charge the battery for 2 hours uninterrupted! Once the pump is turned on, the battery indicator icon on the display will show
the remaining battery life until the battery runs out. When the battery is low the battery indicator icon will start flashing. When the battery is fully charged the indicator
will display a full battery icon. Attention: Battery cannot be charged over 24 hours.
Assembling the pump (Figure IV):
Important:
• Before assembling the pump, make sure that all parts, except the main device, USB cable and the adaptor are cleaned and sterilized.
• Check breast pump kit components for wear or damage before each use. Replace if necessary.
• Always inspect all parts prior to use for cleanliness.
• To prevent damage to the breast pump all components must be completely dry before use.
EN
1. Wash your hands thoroughly with soap and water before touching the breast pump, breast pump kit and the breast.
2. Install the valve and the seal into the bottom of the linker, make sure they are installed in the correct way.
3. Install the silicone diaphragm into the linker.
4. Place the assembled linker into the main device.
5. Insert the milk bottle into the main device.
6. Install the silicone shield or the silicone insert.
When to express milk:
If breastfeeding goes well, it is advisable (unless advised otherwise by your healthcare professional/ breastfeeding advisor) to wait until your milk supply and breastfeeding
schedule are established (normally at least 2 to 4 weeks after giving birth) before you start expressing.
Exceptions:
• If breastfeeding does not go well immediately, expressing regularly can help to establish and maintain your milk supply.
• If you are expressing milk for your baby to be given in hospital.
• If your breasts are engorged (painful or swollen), you can express a small amount of milk before or between feeds to ease the pain and to help your baby latch on more
easily.
• If you have sore or cracked nipples, you may wish to express your milk until they are healed.
• If you are separated from your baby and wish to continue to breastfeed when you are reunited, you should express your milk regularly to stimulate your milk supply.
You need to find the optimum times of the day to express your milk, for example just before or after your baby's first feed in the morning when your breasts are full, or after a
feed if your baby has not emptied both breasts. If you have returned to work, you may need to express during a break.
Using a breast pump requires practice and it may take several attempts before you succeed. Fortunately, the KikkaBoo electric breast pump is easy to assemble and use so you
will soon get used to expressing with it.
Using the pump (Figure V):
1. Wash your hands thoroughly and make sure your breasts are clean.
2. Hold the breast shield onto your breast with your thumb and index finger. Support your breast with palm of your hand. Place your nipple in the center of the assembled sili-
cone shield/insert. Gently press the pump to your breast. Make sure your nipple fits properly.
3. Place your nursing bra above the pump.
4. Turn on the breast pump by прессинг the power button and choose the mode you prefer.
5. Find a comfortable position. Make sure not to lie down or recline.
• The breast pump automatically starts up in simulation mode. You can change the level of the stimulation mode by using the "+" and "-" buttons. After two minutes, it will
automatically transition to pumping mode. If your milk begins to flow before two minutes, press the mode change button to manually transition to pumping mode.
• Once you are in the pumping mode, increase the suction level by using the "+"button until pumping feels slightly uncomfortable (not painful), then decrease slightly using
the "-"button.
Note: stimulation and massage mode are fast sucking pump rhythms, which aim to stimulate milk ¬flow. Pumping mode is slower sucking rhythm for gentle and efficient
milk removal after milk has started fl¬owing.
• When milk flow stops, you can switch to the bionic mode. It aims to trigger another let-down by combining fast and slow pumping rhythms.
Attention: Do not always use the maximum level of each mode, just choose the most comfortable level for you. Depending on your own personal comfort, you may wish to
use a higher suction level that
provides deeper suction. You can always return to a lower suction level.
Note: Do not worry if your milk does not flow immediately. Relax and continue pumping. The milk will soon flow, even if you do not use all the suction power that the pump
can create. The first few times when you use the breast pump, you may need to use a higher suction mode to get your milk flowing.
Warning! Do not pump for more than 5 minutes without interruption. If there is still no milk flow, try expressing at another time of the day.
• When you have finished expressing, turn off the breast pump by pressing the power button for 2 seconds.
EN
Advertenties
Inhoudsopgave
