Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
ASSEMBLING THE BLOWER TUBES
Connecting the Control-Handle Tube to the Bellows
1. For convenient assembly, place the blower with the
support harness facing up as shown in Fig. B1.
2. Loosen and remove the two screws from one side of
the bellows clamp, partly open the bellows clamp but
make sure that the tab on the rim of the bellows is
fully engaged into the slot in the clamp (Fig. B2).
3. Insert the rear end of the control-handle tube into the
bellows until the rear end surface contacts with the
bellows clamp end surface (Fig. B3).
4. The bellows clamp can be fully closed when the
control-handle tube is connected to the bellows
properly. Securely tighten the screws of the bellows
clamp (Fig. B4).
B1-1 Support Harness
B1-2
B2-1 Screws
B2-2
B2-3 Tab
B2-4
Control-handle
B3-1
B3-2
Tube
B3-3 Rear End Surface
B3-4
Connecting the Blower Tube to the Control-Handle
Tube
1. Loosen and remove the quick-release lever and wing
nut from the tube clamp assembly affixed to the
blower tube (Fig. C1).
2. Align the groove in the blower tube with the rib on
the control-handle tube, slide the blower tube over
the control-handle tube as far as it will go (Fig. C2).
3. Insert the pin of the quick-release lever and close the
lever onto the tube clamp (Fig. C3).
4. Tighten the wing nut to secure the tube clamp (Fig. C4).
C1-1 Blower Tube
C1-2
Quick-release
C1-3
C1-4
Lever
Groove of Blower
C2-1
C2-2
Tube
Connecting the Tapered Nozzle to the Blower Tube
1. Align the groove in the nozzle with the latch on the
tube. Push the nozzle over the tube until it securely
snaps into place (Fig. D1).
56 VOLT LITHIUM-ION CORDLESS BACKPACK BLOWER — LBPX1100
2. To remove the nozzle, press and hold the nozzle-
release button to disengage the latch, then pull the
nozzle straight from the blower tube (Fig. D2).
D1-1
OPERATION
WARNING:
to make you careless. Remember that a careless fraction
of a second is sufficient to inflict serious injury.
WARNING:
accessories not recommended by the manufacturer of
this product. The use of attachments or accessories not
recommended can result in serious personal injury.
Bellows
Slot
WARNING:
the product when you are assembling parts, making
Bellows Clamp
adjustments, cleaning, or when not in use. Removing the
batteries will prevent accidental starting that could cause
Rear End
serious personal injury.
Before each use, inspect the entire product for damaged,
Bellows Clamp End
missing, or loose parts, such as screws, nuts, bolts,
Surface
caps,etc. Tighten securely all fasteners and caps and
do not operate this product until all missing or damaged
parts are replaced.
APPLICATION
You may use this product for the purposes listed below:
◾
Clearing leaves and miscellaneous yard debris from
lawns and mulch beds.
◾
Clearing hard surfaces, such as driveways and
walkways.
◾
Keeping decks and driveways free from leaves and
pine needles.
NOTICE:
Tube Clamp
purpose. Any other use is deemed to be a case of misuse.
Wing Nut
ATTACHING/DETACHING THE BATTERY PACK
Use only with EGO's battery packs and chargers listed in
Rib of Control-
Fig. A2.
handle Tube
Refer to corresponding battery packs and chargers
manuals for more details.
Fully charge before first use.
NOTE:
For best performance, we recommend use of the
EGO 56V battery pack BA3360T (6.0 Ah) or other EGO 56V
battery packs with higher Ah rating.
Nozzle-release
D1-2
Latch
Button
Do not allow familiarity with this product
Do not use any attachments or
Always remove the batteries from
The tool is to be used only for its prescribed
EN
9
Advertenties
Inhoudsopgave
