Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
• Do not place any dangerous products, such as fuel, alcohol,
paint, aerosol cans with a flammable propellant, flammable
or explosive substances, etc. inside or near the appliance.
• Once installed, the appliance must not be tilted at an angle
greater than 5° and it is necessary to wait 2h before connect-
ing it to the power supply to switch it on. The same applies if
the appliance is moved afterwards.
• If the appliance has been switched off or disconnected from
the power supply, it is necessary to wait 5 minutes until
switching on again.
• No other appliances should be plugged into the same socket
as with this appliance.
Intended use
• This appliance is intended to be used in household and simi-
lar applications such as:
- staff kitchen areas in shops, offices and others working en-
vironment;
- farm houses;
- by clients in hotels, motels and other residential type en-
vironment;
- bed and breakfast type environment.
• The appliance is designed only for making ice cubes. Any
other use may lead to damage of the appliance or personal
injury.
• Operating the appliance for any other purpose shall be
deemed a misuse of the device. The user shall be solely liable
for improper use of the device.
Grounding installation
This appliance is classified as protection class I and must be
connected to a protective ground. Grounding reduces the risk
of electric shock by providing an escape wire for the electric
current.
This appliance is fitted with a power cord with grounding plug
or electrical connections with grounding wire. The connections
must be properly installed and grounded.
Main parts of the product
(Fig.1 on page 3)
1. Top cover
2. Door
3. Ice-making & water tank assembly
4. Front panel
5. Operation panel
6. Air outlet: Must keep the air circulate smoothly, hot air will
blow out when unit running.
7. Water draining port.
8. Water inlet port for water supply.
Remark: The content of this manual applies for all listed items
unless specified otherwise. The appearance may vary from the
shown illustrations.
Spare parts or accessories
(Fig.2 on page 3)
9. Water drain pipe,
10. Connector for the water faucet
11. Water supply pipe(ø 6.35mm).
12. Ice scoop
Control panel
(Fig.3 on page 4)
13. "Add water" light: When the light flashes, it means the wa-
ter is supplied to slow; and when the light is on always, it
means absence of water in unit.
14. "Timer" light: When this light is on, it means the TIMER is
set. Timer can be set on or off with the clean/timer button.
15. "Ice" light: If the light is on, means the unit is making
ice; And if the light flashes, means the unit is during the
ice-harvest process.
16. "Full" light: When the unit is full of the ice cube, the light
will be on.
17. "Clean" light: When this light is on, water pump cleaning
start. When the light flashes, water pump cleaning stop.
18. "Increase / Decrease" button: Use to adjust the ice-making
process duration period length, the default setting is zero, 1
minute adding or decreasing per each pressing of "Increase
/ Decrease" button. Also to adjust the delay time of the tim-
er, the default setting is zero, 1 hour adding or decreasing
per each pressing of "Increase / Decrease" button.
19. LED Display: At normal condition, the number in the win-
dow is always on, it displays the ambient temperature; And
if the number flashes, it will display the time left in minutes
of each process, like ice-making cycle, self-cleaning pro-
gram, etc.
20. "On / Off" button: When the unit is off, press this button to
turn on the unit; And during the Self-cleaning program,
or normal ice-making state, press this button to turn off
the unit at once; And also if the unit is set with the Timer,
press this button to cancel the Timer setting. When the unit
is making the ice cube, press this button for more than 5
seconds, the unit will switch to ice harvest process by force.
21. "Timer / Clean" button: Quickly press this button once, to
enter the Timer setting program; And press this button for
more than 5 seconds when the machine is off, to enter the
Cleaning program.
Preparation before use
• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all ac-
cessories. In case of incomplete or damaged delivery, please
contact the supplier immediately. In this case, do not use the
device.
• Clean the accessories and the appliance before use (See ==>
Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant
surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in
the future.
• Keep the user manual for future reference.
NOTE! Due to manufacturing residues, the appliance may emit
a light odor during the first few uses. This is normal and does
not indicate any defect or hazard. Make sure the appliance is
well ventilated.
Installation
1. Keep the proper room temperature and inlet water temper-
ature according to above specification table. Otherwise it
will affect the ice making performance.
2. This unit should not be located near any heat source.
GB
11
Advertenties
Inhoudsopgave
