Inhoudsopgave
Advertenties
button 2.3 on the on/off switch (2).
4.2 Setting the light position (Fig. 3)
The upper light can be set to eight positions
positions. To do this, simply move the upper light
into the desired position and snap into place. into
place. The light is now fi xed.
4.3 Mounting the lamp (Fig. 4-11)
The lamp can be attached in a wide variety of
ways ways. - Hook (fi g. 4/item 5):
•
With the hook, the lamp can be quickly and
securely to pipes, cables, railings, scaffolding
or similar. To do this, simply pull the hook (5)
upwards as shown in Fig. 4 until you hear it
click into place. It audibly clicks into place.
•
Upper and lower suspension eye (Fig. 6/Pos.
6+7): Open the two suspension eyelets by
90degrees. The lamp can now be on the two
suspension eyelets (Fig. 7) or hung on the
wall (Fig. 8) or ceiling (Fig. 9). be suspended.
The lamp can also be mounted vertically
using the upper can also be attached verti-
cally (Fig. 10).
•
Battery holder (Fig. 11):
•
The lamp can also be used simply standing
on the standing on the battery (Fig. 11)
4.4 Charging the lithium battery pack
(Fig. 12/13)
1. Remove the battery pack (a) from the battery
mount (8), pressing the push/lock button (b)
downward to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the socket outlet. The green LED will then
begin to fl ash.
3. Push the battery pack onto the battery char-
ger.
In section 8 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
whether there is a voltage at the mains power
socket;
•
whether there is good contact at the charging
contacts of the charging unit
If the battery pack still fails to charge, please send
•
the charging unit
•
and the battery pack
to our customer service center.
Anl_TE_CL_18_1000_S_Li_SPK13.indb 13
Anl_TE_CL_18_1000_S_Li_SPK13.indb 13
GB
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
4.5 Battery capacity indicator (Fig. 12)
Press the battery capacity indicator switch (a).
The battery capacity indicator (b) shows the char-
ge status of the battery using 3 LEDs.
All 3 LEDs lit:
The battery is fully charged.
2 or 1 LED(s) lit:
The battery has an adequate remaining charge.
1 LED fl ashing:
The battery is empty, recharge the battery.
All LEDs fl ashing:
The battery temperature is too high. Remove the
battery from the unit and keep it at room tempera-
ture for one day. If the fault occurs again, the bat-
tery has been deep-discharged and is defective.
Remove the battery from the unit. Never use or
charge a defective battery.
- 13 -
28.08.2024 13:15:50
28.08.2024 13:15:50
Advertenties
Inhoudsopgave
