Inhoudsopgave
Advertenties
NOTICE
SANIWALL
Pro is a wall unit with integrated
®
macerator specially designed for the installation of all
types of wall-hung toilet, shower and washbasin.
SANIWALL
Pro is designed for domestic use only.
®
Installed and maintained correctly, SANIWALL
will deliver a high level of performance, safety and
reliability.
Please pay particular attention to the following:
possible danger to personnel,
warning of potential electrical hazard,
"WARNING" A general warning that failure to
follow instructions could result in poor functioning
of the equipment.
Please contact our customer services for any
additional information.
2
LIST OF SUPPLIED PARTS
(fig.1 and fig.2)
3
DIMENSIONS (fig.3)
I
- Depth of frame = Between 200 and 245mm
II
- Thickness of casing = Between 16 and 100mm
III
- Height = Adjustable to between 1080 and 1280mm
IV
- Bowl height = 400 mm min ( finished floor )
V
- Max. thickness of finished floor = 185 mm
VI
- Height between floor and centre of macerator
discharge outlet = 220 mm mini
4
SANIWALL® Pro MACERATOR :
AREA OF USE AND TECHNICAL DATA
Discharge of toilet waste
Discharge of washbasin waste
Area of use
Discharge of shower waste
Type
Maximum vertical discharge
Voltage
Frequency
Maximum absorbed power
Maximum absorbed current
Appliance class
Protection index
Net weight
WARNING: This equipment should not be used for
purposes other than those described in these
instructions.
5
PERFORMANCE CURVE (fig.5)
COMBINATIONS OF HEIGHT AND LENGTH
6
OF THE DISCHARGE PIPE (fig.6)
7
INSTALLATION (figs. 7.1 to 7.6)
SANIWALL
Installation should only be attempted by qualified
persons.
The macerator must be located in the same room as
the toilet and any other sanitary installations that may
also be connected.
Pro
®
The equipment must be easily accessible for checking
and maintenance purposes.
7.1
7.1.a
1 - WARNING: This frame should be fitted on a load
2 - Measure the centre-to-centre distance (A)
3 - Place the frame in position.
4 - Place the wall fixing lugs
5 - Using a hacksaw, cut off any excess threaded rod
7.1.b
1 - Place the frame in its desired position.
2 - Unscrew the 4 set screws
3 - Adjust the height of the feet so that the front of the
P 30
5m
4 - Check that the frame is horizontally level and
220-240 V
50 Hz
400 W
1.8 A
7.1.c
I
1 - Mark out your drill points
IP44
5.6 KG
2 - Move the frame away and, using a 10mm bit, drill
3 - Insert the dowels
4 - Reposition the frame and move on to connecting
is designed to be flush-mounted.
Pro
®
PREPARING THE FRAME
FITTING THE TOILET BOWL ANCHOR RODS
AND FIXING TO THE WALL
bearing wall if the floor structure is lightweight or
on a partition wall if the floor slab is suitable (NF
safety test: 400kg for wall-hung bowl). For
packaging purposes, the feet are folded inwards.
To reposition them correctly, they should be turned
outwards by a quarter turn.
between the bowl anchoring holes: there are only
2 possible measurements: (Ka = 230 mm ) and
(Kb = 180 mm).
Insert the rods
K
into the holes of the frame, as
per the centre-to-centre distance and fix them in
place using the nuts.
fix them to the frame using the nuts, after having
checked that the frame is vertical
from the fixing lugs.
ADJUSTING THE HEIGHT OF THE FRAME
bowl is 400mm from the finished floor.
retighten the 4 set screws
PREPARING FIXING
(2 on the wall and 6 on the floor).
2 holes (min. depth 70mm) in the wall.
Use an 8mm bit to drill 6 holes (min. depth 65mm)
in the floor.
q
and
the SANIWALL
macerator.
Pro
®
y
against the wall and
s
.
s
.
x
into the holes.
Advertenties
Inhoudsopgave
