Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Flying the 4-channel Quadrocopter
NOTE!
Take care particularly in the first few flights to move
the lever on the controller very gently and not over-
hurriedly. As a rule, only very small movements of the
respective levers are necessary to carry out the desired
control commands!
If you notice that the Quadrocopter moves forwards or to the
side without your touching the respective lever, please adjust
the trim of the Quadrocopter as described in (
+/- Gas (up / down)
9
To start or to fly higher, push the gas lever on the
left cautiously forwards. To land or fly lower, push
the gas lever on the left cautiously backwards.
To make the Quadrocopter circle to the left or the
10
right on the spot, move the lever on the left cau-
tiously to the left or the right.
To fly the Quadrocopter to the left or the right,
11
push the lever on the right cautiously to the left or
the right.
To fly the Quadrocopter forwards or backwards,
12
push the lever on the right cautiously forwards or
backwards.
Looping function
WARNING! ONLY FOR EXPERIENCED PILOTS!
When you press the looping button, an audi-
13a
ble signal sounds until you move the right-hand
joystick either up or down, or right or left. The
Quadrocopter then carries out the loop or roll in
the respective direction. Before you do this, make
sure you have ample room on all sides (about
2.5 m – 8').
Beginner/Advanced switch
WARNING! 100 % IS ONLY FOR EXPERIENCED PILOTS!
30 % = beginner mode
13b
Signal sounds once on switching over. Looping
the loop and rollovers are possible as explained
13a
in
.
60 % = medium mode
The quadrocopter reacts more sensitively than
in 30 % mode. Signal sounds twice on switching
over. Looping the loop and rollovers are possible
13a
as explained in
.
100 % = advanced mode -> 3D mode.
The Quadrocopter reacts very sensitively to joy-
stick movements. Signal sounds three times on
switching over.
Trimming the Quadrocopter
When hovering, if the Quadrocopter flies to the left
14
or right without you moving the lever for left / right
movement, please proceed as follows:
If the Quadrocopter moves on its own fast or slow
sideways to the left, press the lower right trimmer
for right / left tilt in steps to the right. If the Quad-
rocopter moves right, press the trimmer for right /
left tilt in steps to the left.
14
15
16
).
When hovering, if the Quadrocopter flies forwards
15
or backwards without you moving the lever for for-
wards or backwards movement, please proceed
as follows:
If the Quadrocopter moves on its own fast or
slow forwards, press the upper right trimmer for
forwards / backwards in steps downwards. If the
Quadrocopter moves backwards, press the trim-
mer for forwards / backwards in steps upwards.
When hovering and without you moving the lever
16
for circling on the spot, if the quadrocopter rotates
to left or right, proceed as follows: If the quadro-
copter rotates quickly or slowly to the left around
its own axis, press the trimmer for rotation below
left in steps to the right. If the quadrocopter rotates
to the right, press the trimmer for rotation in steps
to the left.
Changing the rotor blades
Use a screwdriver if it is necessary to remove a ro-
17
tor blade. Make sure that you draw the rotor blade
with great care vertically upwards, and hold the
motor from below to stabilise it. Screw the rotor
blade firmly back on to the quadrocopter.
WARNING!
18
Be sure to note the marking and colour, also the tilt
angle of the rotor blades!
Front left: red – marking "A"
Front right: red – marking "B"
Rear right: black – marking "A"
Rear left: black – marking "B"
WARNING! Before you first fly the model, find out
w hether there is a legal requirement to insure model
aeroplanes such as this in your country.
Troubleshooting
Problem: Remote control does not work.
Cause:
Solution: Turn the ON/OFF-power switch "ON".
Cause:
Solution: Check if the batteries have been correctly inserted.
Cause:
Solution: Insert new batteries.
Problem: The Quadrocopter cannot be controlled with the
Cause:
Solution: First turn the power switch on the remote control
Cause:
Solution: Please carry out the binding procedure as de-
Problem: The Quadrocopter does not lift.
Cause:
Solution: Push the throttle up.
Cause:
Solution: Charge the battery (see chapter "Charging the
Problem: During flight, the Quadrocopter loses speed and
Cause:
Solution: Charge the battery (see chapter "Charging the bat-
Problem: The quadrocopter only flies in a circle or turns
Cause:
Solution: Fit rotor blades / replace rotor blades as de-
For the latest version of these operating instructions
and information on replacement and spare parts avail-
able, please visit carrera-rc.com in the service area.
Errors and changes excepted
Colours / final design – changes excepted
Technical changes and design-related changes excepted
Pictograms = symbolic photos
9
The ON/OFF-power switch is turned "OFF".
The batteries have been wrongly inserted.
The batteries do not have enough power.
remote control
The power switch on the reomote control is turned
"OFF".
"ON".
The remote control is possibly not correctly frequen-
cy bound with the receiver on the Quadrocopter.
scribed in "Checklist for flight preparation".
The rotor blades rotate too slowly.
The battery´s power is not sufficient.
battery").
height without any obvious reason.
The battery is too weak.
tery").
over on starting.
Rotor blades incorrectly fitted or damaged.
scribed in
17
18
.
Advertenties
Inhoudsopgave
