Inhoudsopgave
Advertenties
Guidelines and warnings for the use of LiPo recharge-
able batteries
• You have to charge the attached 3.7 V
650 mAh/2,405 Wh
LiPo rechargeable battery in a safe place and at a safe
distance to flammable material.
• Never leave the battery unattended while it is charging
• After a flight, the rechargeable battery has to cool down to
the ambient air temperature before charging it.
• You must always use the corresponding LiPo charging unit
(USB cable / remote control). In case of non-compliance
with these directions there is a danger of fire resulting in
a health risk and/or damage to property. NEVER use any
other battery charger.
• Should the rechargeable battery swell or deform while dis-
charging or recharging, you have to immediately stop charg-
ing or discharging the battery. Take the battery out as quickly
and carefully as possible and place it in a safe and open area
offside any inflammable material and watch it for at least 15
minutes. In case you continue charging or discharging a bat-
tery which has already started to swell or deform there is a
danger of fire! Even in case of slight deforming or ballooning
the rechargeable battery has to be taken out of operation.
• Store the rechargeable battery at ambient temperature in a
dry place.
• A lways recharge the battery immediately after use to prevent
its becoming deep discharged. Please make sure to allow a
pause of about 20 minutes between finishing the flight and
recharging the battery. Recharge the battery occasionally
(suggested every 2-3 months). Failure to treat the battery as
described above can lead to its becoming defective.
• When transporting or temporarily storing the rechargeable
battery the temperature should be between 5-50°C. If pos-
sible, do not store the battery or the model in a car and do
not expose it to direct sunlight. In case the battery is broiled
it can be damaged or catch fire.
Note: If the battery voltage/output is low you will recognise
that a considerable trim and/or controlling is necessary to
avoid that the Quadrocopter starts trundling. This usually
occurs before reaching a battery voltage of 3 V and it is a
good moment to end the flight.
Contents of package
1 x Quadrocopter
1
1 x Controller
1 x USB charging cable
1x Rechargeable Battery
1x Lanyard
1 x Set of replacement parts
6 x 1.5 V Mignon AA batteries
(non-rechargeable)
Recharging the LiPo rechargeable
battery
Make sure you only charge the LiPo rechargeable battery
supplied with the LiPo charging unit also supplied (USB ca-
ble and remote control). If you try to charge the rechargeable
battery with a different LiPo battery charger or any other bat-
tery charger, this might cause serious damage. Please care-
fully read the previous chapter with warnings and guidelines
on the usage of rechargeable batteries before proceeding.
Supply terminals are not to be short-circuited.
You can charge the rechargeable battery fitted in the Quadrocop-
ter with its USB charging cable from a USB port on a computer:
Charging via computer:
2a
• R echargeable batteries are to be removed
from the model before being charged.
• Connect the USB charging cable with the USB
port of a computer. The LED on the USB charger
cable lights green indicating that the charger unit
is correctly connected to the computer. If you
plug in a Quadrocopter with a discharged bat-
tery, the LED on the USB charging cable lights
up red and shows that the Quadrocopter battery
is being charged. The USB charging cable and
the charging socket on the Quadrocopter are de-
signed to make incorrect connection impossible.
• It takes about 60 minutes to recharge a dis-
charged battery (but NOT a deep-discharged
one). When the battery is fully charged, the
LED display on the USB charger cable lights up
green again.
Note: when supplied, the lipo-battery is already partially
charged. So the first charging cycle may well take less time.
It is essential to follow the connection sequence given
above! If you have the charger cable only connected to
the quadrocopter, and not to a source of electricity, a
green LED display indicates that there is still power in
the battery. The green LED display does not necessarily
indicate the battery is still adequately charged.
Undo the plugged connection on the Quadrocopter
when you are not using the Quadrocopter. Failure to ob-
serve this precaution may cause battery damage!
Inserting the batteries in the
remote control
Open the battery compartment with a screwdriver
3
and insert the batteries in the remote control.
Please keep in mind the correct polarity. After
having closed the compartment you can check all
functions of the remote control with the help of the
power-switch on the front.
With the power switch turned ON and functioning
correctly, the top centre LED on the remote con-
trol will light up red.
When the control LED flashes rapidly, the batter-
ies in the controller must be changed.
Frequency bind between model
and remote control
The Carrera RC Quadrocopter and the remote
4
control are frequency bound at purchase. If ini-
tially there are any problems with communication
between the Carrera RC Quadrocopter and the
remote control, please carry out a new frequency
bind.
• Connect the battery in the model.
• The LEDs on the quadrocopter now flash rhyth-
mically.
• Switch on the controller at the power switch.
• Push the left-hand joystick, i.e. the throttle lever,
right to the top, then fully downwards into the
zero position.
• The binding has now been successfully estab-
lished. The LED on the controller now lights con-
tinuously.
• WARNING! Immediately after switching it on,
place the Quadrocopter on a flat and level
surface. The gyro-system will then set itself
automatically.
Range of functions of the
remote control
1. Aerial
5
2. Power switch (ON / OFF)
3. Control LED
4. Gas
Circling
5. Forwards / backwards
right / left banking
6. Trimmer for right / left banking
7. Trimmer for forwards / backwards
8. Trimmer for rotation
9. Looping Button
10. Beginner/Advanced switch (30% / 60% / 100%)
11. Battery compartment
3
8
Description of the Quadrocopter
1. Rotor system
6
2. Rotor protection cage
3. LEDs
4. Battery cable
7
5. Quadrocopter connecting plug
Choosing the flight area
The Quadrocopter may be flown outdoors.
8
When you have trimmed your Quadrocopter
properly and are thoroughly familiar with its
controls and how it can perform, you can then
start to fly it in smaller and more confined
spaces. Please be aware that, although it may
be calm on the ground, it may still be very
windy even a little way off the ground. If this
warning is disregarded, it may lead to total
loss of the Quadrocopter.
Checklist for flight preparation
This checklist is not a substitute for the contents of the oper-
ating instructions. Although it can be used as a quick-start-
guide, we strongly recommend you first to read the operating
instructions in detail before you proceed.
• Check the contents of the package.
• Connect the charging unit to the source of power.
• Charge the lipo-battery as described in the section
"Recharging the LiPo rechargeable battery".
• Fit 6 AA batteries in the controller, making sure their polar-
ity is correct.
• Look for a suitable environment for flying.
• Slide the battery into the battery bay on the bottom of the
Quadrocopter.
2b
• Connect the battery in the model.
• WARNING! Immediately after switching it on, place the
Quadrocopter on a flat and level surface. The gyro-
system will then set itself automatically.
• The LEDs on the quadrocopter flash red.
• Switch on the controller at the ON/OFF switch. Be sure to
check the Beginner-Advanced switch (
left-hand joystick, i.e. the throttle lever, right to the top, then
fully downwards into the zero position.
• Allow the Quadrocopter a few moments until the system is
correctly initialised and is ready for operation. The LED in
the Quadrocopter now lights continuously. The LED on the
controller now lights continuously.
• Repeat the above points as required, if you wish to fly more
Quadrocopters at the same time.
• Check the control system.
• Make yourself familiar with the control system.
• Trim the Quadrocopter as necessary as described under
14
15
16
, so that when hovering it no longer moves
from the spot without a command from the controller.
• The Quadrocopter is now ready to be flown.
• If the Quadrocopter displays no functions, retry the above
binding procedure.
• Fly the model.
• Land the model.
• Disconnect the battery plug connection.
• Always switch off the remote control last.
13b
). Push the
Advertenties
Inhoudsopgave
