Advertenties
Beschikbare talen
Beschikbare talen
Slide the rubber sanding pad (18) onto the grinding spindle
(16).
Screw on the round nut (20) and tighten with the two-pin
spanner.
Press the sanding sheet (19) firmly onto the underside of
the rubber sanding pad (18).
Cup brush/disc brush
Always fit the hand guard (17) when working with the
u
cup brush or disc brush.
See the graphics page for fitting instructions.
The cup brush/disc brush must be screwed onto the grinding
spindle until it rests firmly against the grinding spindle flange
at the end of the grinding spindle thread. Tighten the cup
brush/disc brush with an open-ended spanner.
Carbide Grinding Head
A grinding head may be used only with a suitable pro-
u
tective guard.
Quick-clamping nut
To change the abrasive tool easily without having to use any
additional tools, you can use the quick-clamping nut (13) in-
stead of the clamping nut (12).
The quick-clamping nut (13) may be used only for
u
grinding or cutting discs.
Only use quick-clamping nuts (13) that are in good work-
ing order and not damaged.
When screwing on, make sure that the printed side of the
quick-clamping nut (13) is not facing the grinding disc;
the arrow must be pointing towards the index mark (24).
(24)
Bosch Power Tools
Press the spindle lock but-
ton (1) to lock the grinding
spindle. To tighten the
quick-clamping nut, turn
the grinding disc firmly
clockwise.
If the quick-clamping nut
has been attached correctly
and is not damaged, you
can loosen it by hand by
turning the knurled ring an-
ticlockwise. If the quick-
clamping nut is stuck, do
not attempt to loosen it
with pliers – always use
the two-pin spanner. Posi-
tion the two‑pin spanner as
shown in the figure.
Approved abrasive tools
You can use all the abrasive tools mentioned in these operat-
ing instructions.
-1
The permissible speed [min
] or the circumferential speed
[m/s] of the abrasive tools used must at least match the val-
ues given in the table.
It is therefore important to observe the permissible rota-
tional/circumferential speed on the label of the abrasive
tool.
max. [mm]
D
b
100
7
115
7
125
7
100
–
115
–
125
–
70
30
75
30
82
–
Rotating the Machine Head
Pull the plug out of the socket before carrying out any
u
work on the power tool.
chine head carefully, without removing it from the hous-
ing, into the new position. Screw in and retighten the four
screws.
Dust/Chip Extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
English | 21
[mm]
-1
d
[min
]
[m/s]
16.0
11000
80
22.2
11000
80
22.2
11000
80
–
11000
80
–
11000
80
–
11000
80
M10
11000
45
M14
11000
45
M14
11000
80
The machine head can be
rotated in 90° increments.
In this way, the on/off
switch can be brought into
a more favourable handling
position for particular ap-
plications, e.g. for left-
handed tool users.
Completely unscrew the
four screws. Rotate the ma-
1 609 92A 6KJ | (28.05.2021)
Advertenties
