Advertenties
Beschikbare talen
Beschikbare talen
OBJ_BUCH-280-006.book Page 16 Thursday, August 25, 2016 5:34 PM
16 | English
Technical Data
Cut-off Grinder
Article number
Rated power input
Output power
Rated speed
Max. diameter for diamond cutting discs
Cutting discs width, min.
Cutting discs width, max.
Thread of grinder spindle
Thread length (max.) of grinder spindle
Max. cutting depth with cutting guide
Reduced starting current
Weight according to EPTA-Procedure 01:2014
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Only for power tools without reduced starting current: Starting cycles generate brief voltage drops. Interference with other equipment/machines may
occur in case of unfavourable mains system conditions. Malfunctions are not to be expected for system impedances below 0.25 ohm.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-22.
Typically the A-weighted noise levels of the product are:
Sound pressure level 105 dB(A); Sound power level
116 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 60745-2-22:
2
2
a
=6.5 m/s
, K <1.5 m/s
.
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
1 609 92A 2CD | (25.8.16)
GWS 24-300
3 601 C64 3..
W
2400
W
1670
-1
min
5000
mm
300
mm
3.2
mm
4.0
M 14
mm
32
mm
100
kg
10.3
/II
Assembly
Mounting the Protective Devices
Before any work on the machine itself, pull the mains
plug.
Operate the machine only with the protection guard
and the bow handle mounted.
Protection Guard for Cutting
For cutting with diamond-tipped abrasives, always use
the protection guard for cutting 6.
Provide for sufficient dust extraction when cutting
stone.
Release the clamping lever 8. Place the protection guard 6
with the encoding key 17 engaging into the groove on the
spindle collar until the shoulder of the protection guard is
seated against the flange of the power tool, and turn the pro-
tection guard 6 to the requested position. Lock the clamping
lever 8.
Adjust the protection guard 6 in such a manner that
sparking is prevented in the direction of the operator.
The tensioning force of the clamping lever is preset for tight
seating of the protection guard 6. By tightening the adjust-
ment screw 7, the tensioning force can be increased. Pay at-
tention to the tight seating of the protection guard 6 and
check it regularly.
Note: The encoding keys on the protection guard 6 ensure
that only a protection guard that fits the machine type can be
mounted.
Bow Handle
Fasten the bow handle 1 to the gear case as shown in the fig-
ure.
GWS 24-300 J
3 601 C64 8..
2400
1670
5000
300
3.2
4.0
M 14
32
100
–
10.3
/II
Bosch Power Tools
Advertenties
