Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
en
26
overheating of the power tool and the materials being
sanded, empty the dust collector/container in time,
observe the material manufacturer's working instruc-
tions, as well as the relevant regulations in your country
for the materials being worked.
Operating Instructions.
The self-start lock prevents the cordless straight
grinder from automatically restarting again after a
power interruption, e.g., after changing the battery. In
this case, switch the power tool off, remove it from the
workpiece and check the application tool. Afterwards,
switch the power tool on again.
Use a collet that fits the grinding accessory.
Insert the clamping shaft of the grinding accessory to
the stop into the collet chuck.
Observe the maximum permitted projecting shaft
length (a) of the grinding accessory according to the
manufacturer's instructions (see page 10).
Move the power tool back and forth applying uniform
pressure, so that the workpiece surface does not
become too hot.
For best performance, operate the power tool only
with FEIN ProCORE batteries or with ProCORE batter-
ies of AMPShare partners. When using other batteries,
the functionality can be limited.
Additional operating instructions.
The self-start prevention lock prevents the power tool
from automatically starting when the battery is inserted
while the on/off switch is set to on.
If the power tool shuts off without the switch being
actuated, switch the power tool switch off, remove the
battery and reattach it.
Charge-control Indicator on the Battery (see
page 9).
The charge condition can be indicated by the green
LEDs of the charge-control indicator on the battery.
Press the charge-control indicator button
to indicate the charge condition.
When no LED lights up after pressing the charge-con-
trol indicator button, the battery is defective and must
be replaced.
Transport.
The Li-ion batteries are subject to the Dangerous
Goods Legislation requirements. The user can trans-
port the batteries by road without further require-
ments.
When being transported by third parties (e.g.: air trans-
port or forwarding agency), special requirements on
packaging and labelling must be observed. For prepara-
tion of the item being shipped, consulting an expert for
hazardous material is required.
Dispatch batteries only when the housing is undam-
aged. Tape or mask off open contacts and pack up the
battery in such a manner that it cannot move around in
the packaging. Please also observe possibly more
detailed national regulations.
Repair and customer service.
Please observe that power tools may only be
repaired, maintained and inspected by qualified
electricians, as improper maintenance can result in con-
siderable hazards for the user.
dust to settle in the interior of the power tool. Blow
out the interior of the power tool via the ventilation
slots frequently with dry and oil-free compressed air.
When working gypsum-containing materials, dust can
settle within the power tool and switch element, which
can harden in connection with humidity. This can
impair the switching mechanism. Blow out the interior
of the power tool via the ventilation slots and the
switch element frequently with dry and oil-free com-
pressed air.
Products that have come into contact with asbestos
may not be sent in for repair. Dispose of products con-
taminated with asbestos according to the applicable
country-specific regulations for such disposal.
For FEIN power tools and accessories in need of repair,
please contact your FEIN after-sales service. The
address can be found on the Internet under
www.fein.com.
Renew stickers and warning indications on the power
tool when aged and worn.
The current spares parts list for this power tool can be
found on our website at www.fein.com.
If required, you can change the following parts your-
self:
Application tools, collet
Maintenance and cleaning.
Occasionally clean the ventilation slots and the battery
terminals with a soft, clean and dry brush.
– Do not use chemical substances for cleaning the bat-
tery.
or
Warranty and liability.
The warranty for the product is valid in accordance
with the legal regulations in the country where it is mar-
keted. In addition, FEIN also provides a guarantee in
accordance with the FEIN manufacturer's warranty dec-
laration.
The delivery scope of your power tool may include
only a part of the accessories described or shown in this
Instruction Manual.
When working metal under extreme oper-
ating conditions, it is possible for conductive
Advertenties
Inhoudsopgave
