Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
en
22
For your safety.
Read all safety warnings and all
WARNING
instructions. Failure to follow the
warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have
thoroughly read and completely understood this
Instruction Manual and the enclosed "General
Safety Instructions" (document number
3 41 30 054 06 1). The documents mentioned should
be kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial
safety regulations.
Intended use of the power tool:
Hand-guided straight grinder for dry grinding of metal
with small grinding accessories (grinding points) for
shaping metal with hard metal cutters and for cut-off
grinding.
AGSZ18-90LBL AS (**): This power tool is addition-
ally intended for wire-brushing and polishing in
weather-protected environments with the accessories
recommended by FEIN.
Safety warnings common for grinding, wire
brushing, polishing, carving, sanding or abrasive
cutting-off operations:
AGSZ18-280BL AS (**), AGSZ18-280LBL AS (**): This
power tools are intended to function as a grinder, carv-
ing or cut-off tools.
AGSZ18-90LBL AS (**): This power tool is intended addi-
tionally to function as a wire brush or polisher.
Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to
follow all instructions listed below may result in electric
shock, fire and/or serious injury.
AGSZ18-280BL AS (**), AGSZ18-280LBL AS (**): Opera-
tions such as sanding, wire brushing or polishing are
not recommended to be performed with this power
tools.
AGSZ18-90LBL AS (**): Operation as sanding are not
recommended to be performed with this power tool.
Operations for which the power tool was not designed
may create a hazard and cause personal injury.
Do not use accessories which are not specifically
designed and recommended by the tool manufacturer.
Just because the accessory can be attached to your
power tool, it does not assure safe operation.
The rated speed of the accessory must be at least equal
to the maximum speed marked on the power tool.
Accessories running faster than their rated speed can
break and fly apart.
The outside diameter and the thickness of your acces-
sory must be within the capacity rating of your power
tool. Incorrectly sized accessories cannot be adequately
guarded or controlled.
Grinding wheels, sanding drums or other accessories
must exactly fit the grinder spindle or collet of your
power tool. Application tools that do not fit exactly in
the tool holder of the power tool will run out of bal-
ance, vibrate excessively and may cause loss of control.
Grinding wheels, sanding drums or cutting tools
mounted on a mandrel, or other accessories must be
fully inserted into the collet or chuck. The "projecting
end" as well as the free part of the mandrel between
the grinding accessory and the collet/chuck must be
minimal. If the mandrel is insufficiently clamped or if the
overhang of the grinding accessory is too long, the
application tool may become loose and ejected at high
velocity.
Do not use damaged application tools. Before each use,
check application tools such as grinding wheels for
chips and cracks, sanding drums for cracks, wear or
heavy use, and wire brushes for loose or broken wires.
If the machine or application tool is dropped, inspect for
damage or install an undamaged application tool. After
inspecting and installing the application tool, position
yourself and bystanders away from the plane of the
rotating application tool and run the machine at maxi-
mum no-load speed for one minute. Damaged applica-
tion tools will normally break apart during this test
time.
Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing pro-
tectors, gloves and workshop apron capable of stopping
small abrasive or workpiece fragments. The eye pro-
tection must be capable of stopping flying debris gener-
ated by various operations. The dust mask or respirator
must be capable of filtrating particles generated by your
operation. Prolonged exposure to high intensity noise
may cause hearing loss.
Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal pro-
tective equipment. Fragments of workpiece or of a bro-
ken accessory may fly away and cause injury beyond
immediate area of operation.
Hold the power tool by insulated gripping surfaces only,
when performing an operation where the cutting acces-
sory may contact hidden wiring. Cutting accessory con-
tacting a "live" wire may make exposed metal parts of
the power tool "live" and could give the operator an
electric shock.
Always hold the power tool firmly when starting it. The
reaction torque of the motor, as it accelerates to full
speed, can cause the power tool to twist.
If possible, use clamps to fasten or affix the workpiece.
Never hold a small workpiece in one hand and the
power tool in the other hand while in use. Clamping
small workpieces allows you to use both hands for bet-
ter control the power tool. Round material such as
dowel rods, pipes or tubing have a tendency to roll
away while being cut, and may cause the application
tool to jam or bind and be thrown toward you.
Advertenties
Inhoudsopgave
