Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Chapter 2, OPERATION
Step 3: The correct use of 'SAVE'
The 'SAVE' function allows you to limit the temperature.
When this function is activated, the heater will automati-
cally switch off, when the room temperature exceeds the
set temperature by 2°C. Subsequently, when the room
temperature has dropped again to the set temperature,
the heater will automatically switch on again. Activate
the 'SAVE' setting by pressing the appropriate button.
The SAVE indicator light will light up. Switch off the
function by pressing the SAVE button once again.
Without the 'SAVE' setting your heater will
maintain the set temperature by approxima-
tion as well, by adjusting its heating capacity.
'SAVE' is an economy setting, which you can
use when, for instance, you are not present in
the room or to keep it frost-free.
Step 4: The 'FUEL' indicator light
When the FUEL indicator light lights up, it means that
there is only fuel left for 10 more minutes. The count-
down of the remaining heating time can be seen in the
information display. You remove the fuel tank and
refill it outside the living room. If you don't refill it,
you will hear an alarm signal every two minutes, warn-
ing you to refill the removable tank and after 10 min-
utes the heater will switch off automatically.
6. Timer operation
The timer allows you to switch on the heater automati-
cally at a preset time.
In order to switch on the timer, the correct time must
have been set and the heater should be off. Follow the
procedure below:
[1] Press the TIMER button. The TIMER light and the
information display will start blinking.
[2] Use the adjustment buttons to set the time at which
the heater must ignite. Use the button on the left
( hour) to set the hours and the button on the right
( min.) to set the minutes (interval of 10 minutes).
[3] Press the ON/OFF button while the information dis-
play is blinking.
[4] After approximately 10 seconds the information dis-
All manuals and user guides at all-guides.com
To clear the timer setting, press the ON/OFF button once.
Room temperature
More than 15°C
0°C ~ 15°C
Less than 0°C
7. Room temperature sensor
The room temperature sensor is fitted with a 2.5 meter
cable. This is located on the back of the heater. Ensure
that the cable does not touch the outlet tube. The
room temperature sensor can be installed with cello
tape or with a wood screw.
Select the location where the sensor is to be installed in
such a way that it will not be exposed to direct sun-
light, draughts or the warm air flowing out of the
heater.
8. Childproof lock
The childproof lock can be used to prevent children
accidentally changing the heater settings. When the
heater is burning and the childproof lock is on, the
heater can only be switched off. Other functions are
blocked then. If the heater has already been switched
off, the childproof lock also prevents accidental ignition
of the heater. Activate the childproof lock by pressing
the appropriate button and holding it down for more
than 3 seconds. The KEY-LOCK indicator light will light
up, indicating that the childproof lock has been activat-
ed. Switch off the childproof lock by pressing the but-
ton and holding it down for more than 3 seconds once
again.
9. Switching off the heater
There are two ways to switch off the heater.
[1] Press the ON/OFF button. The information display
play will show CLOCK again and the TIMER indicator
light will light up, indicating that the timer function
has been activated.
Note: When the room temperature is less than
15°C, the preset time is changed automatically
depending on the room temperature in order
to heat the room by the desired time.
Ignition time
Set time
10 minutes before set time
20 minutes before set time
44
Advertenties
Inhoudsopgave
