Inhoudsopgave
Advertenties
Beschikbare talen
Beschikbare talen
Do not use the product near heat sources
such as radiators or devices emitting heat .
The product is only suited for use with the
built-in LED control gear .
The product continues to draw a small amount
of power even if the product is off as long
as product is connected to supply mains . To
switch the product off completely, unplug the
mains plug from the socket-outlet .
Luminaires shall not be connected after each
other .
The product can be hung up or it can be used
on a flat, stable surface, e .g . floor or table .
The product must not be used as a hand
lamp .
Do not mount the product to a wall or ceiling .
The product may only be used as described
in this user manual .
˜ First use
˜ Unpacking the product
1 .
Take the product out of the packaging and remove all
packaging materials and plastic wrappings .
2 .
Check to make sure that all listed parts are included
(see "Scope of delivery") .
3 .
Check whether the product and all parts are in good
condition . If any damage or defect is detected, do not use
the product, but follow the procedure described in chapter
"Warranty" .
˜ Setting up the product
(Fig . D, E)
1 .
Place the base
on a stable, horizontal surface .
[
6 ]
2 .
Loosen the star knob screw
and flat washer
from the base
[
11 ]
3 .
Place the main unit onto the base
4 .
Fix the main unit to the base
screw
including spring washer
7 ]
[
5 .
Loosen both wing screws
desired angle . Tighten both wing screws .
6 .
Check the stability of the product .
including spring washer
7 ]
[
.
6 ]
[
.
[
6 ]
with the star knob
6 ]
[
and flat washer
12 ]
[
11 ]
[
. adjust the main unit at the
[
10 ]
˜ Usage
˜ Switching the product on/off
m
NOTICE! RISK OF PROPERTY DAMAGE! Do not
move the mains cord
to a socket-outlet . There is a risk that the product will slip
or tip over .
INFO: Connect the mains plug
during outdoor use .
Connect the mains plug
o
Switching on: Press the on/off switch
o
(normal brightness) or II (max . brightness) .
Switching off: Press the on/off switch
o
˜ Connecting an external appliance to
the socket-outlet
m
WARNING! RISK OF FIRE! Do not connect any
appliance with a total power consumption of more
than 2,500 W (HG10492/HG10492-FR) or 2,300 W
(HG10492-CH) .
m
WARNING! RISK OF ELECTRIC SHOCK! Water may
enter the product if you connect an appliance featuring
a non-waterproof mains plug . When using the product
outdoors, make sure that the appliance to be connected to
the socket-outlet
For HG10492/HG10492-FR:
The socket-outlet
Only insert a corresponding IPX4 mains plug for outdoor
use .
For HG10492-CH:
The socket-outlet
Only insert a corresponding IPX5 mains plug for outdoor
use .
1 .
Open the socket-outlet cover
2 .
Connect the mains plug of your appliance to the socket-
outlet
.
[
5 ]
[
12 ]
3 .
After use, disconnect the mains plug of your appliance
from the socket-outlet
˜ Cleaning
.
Never immerse the product in water or other liquids .
Otherwise the product can be damaged .
Before cleaning:
o
Remove the mains plug
–
Allow the product to cool down .
–
Close the socket-outlet cover
–
after connecting the mains plug
8 ]
[
to an IPX4 socket-outlet
[
8 ]
to a suitable socket-outlet .
8 ]
[
to position I
[
4 ]
to position O .
[
4 ]
features a waterproof mains plug .
[
5 ]
is only IPX4 protected .
5 ]
[
is only IPX5 protected .
[
5 ]
.
3 ]
[
. Close the socket-outlet cover
[
5 ]
from the socket-outlet .
8 ]
[
.
3 ]
[
GB/IE/NI
.
3 ]
[
9
Advertenties
Hoofdstukken
Inhoudsopgave
